General Safety Instructions; Overview Of The Components; Instruction Manual - AEG SRR 4303 Instrucciones De Servicio

General safety instructions

To avoid the risk of fi re or an electric shock, you should
not expose the device to rain or moisture. Consequently,
do not use the device in the immediate vicinity of water
- for example near a bath tub, a swimming pool or in a
damp cellar.
Use the device only for the intended purpose.
Only connect the device at a properly installed plug
socket. Pay attention that the specifi ed voltage corres-
ponds to the voltage of the plug socket.
When using external mains supply, pay attention to the
correct polarity and voltage. Always place the batteries
in the correct direction.
Assemble the device in such a way that the available
ventilation openings are not covered.
Never open the housing of the device. Incorrect repairs
can constitute a considerable risk for the user. Should
the device become damaged, in particular the mains
supply cable, do not operate the device any longer, but
rather have it repaired by an expert. Check the mains
supply cable regularly for damage.
For safety reasons a broken or damaged mains lead may
only be replaced by an equivalent lead from the manuf-
acturer, our customer service department or a similary
qualifi ed person.
If the device is not used for a longer period, remove the
plug connector from the plug socket or take out the
batteries.
These symbols may be found on the machine and are
intended to indicate the following:
The lightning symbol should advise the user
of parts in the inside of the device which carry
dangerously high voltage levels.
The symbol with an exclamation mark should
advise the user of important operation or
maintenance instructions in the accompa-
nying documentation.
Devices bearing this symbol work with a
„class 1 laser" for tracing the CD. The built-in
safety switches should prevent the user being
exposed to dangerous laser light, which is
invisible to the human eye, when the CD compartment
is opened.
Under no circumstances should these safety switches
be bypassed or manipulated, as this could result in a
danger of exposure to the laser light.
32
5....-05-SRR 4303 AEG 32

Overview of the Components

1 ON control lamp
2 Function selector switch
(RADIO/TAPE/OFF/CD/MP3)
3 BAND selector switch (AM/FM/FM ST)
4 BASS On/off switch
5 VOLUME
6 Aerial
7 TUNING control
8 Station scale
9 Handle
10 Cassette compartment
11 PULL fl ap
12 b Recording key - cassette
13 Playback key - cassette
14 reverse button - cassette
15 forward button - cassette
16 / Stop/Eject key - cassette
17 II Pause key - cassette
18 CD compartment
19 OPEN button – CD compartment
20 CD Display
21 PROGRAM button
22 SKIP - button (reverse search)
23 + 10 button
24 – 10 button
25 REPEAT button
26 SKIP + button (forward search)
27 PLAY/PAUSE button
28 STOP button
headphone connection
29
30 Battery compartment
31 AC connection
Start-up of the device/Introduction
• Please read the operating instructions carefully
before using the radio recorder for the fi rst time!
• Select a suitable location for the radio recorder, such
as a dry, fl at, non-slip surface on which it is easy to
operate the machine.
• Ensure that the radio recorder is suffi ciently ventila-
ted!
Power supply
Connect the power cable supplied (e.g. battery com-
partment (30)) to a properly installed 230 V/50 Hz safety
power socket and the mains connector on the back of
the machine. Ensure that the voltage is the same as that
indicated on the model identifi cation plate. The ON (1)
control lamp shows the function.
Inserting the Batteries (not supplied)
• Open the lid of the battery compartment (30) on the
back.
• Insert 6 batteries of type MONO R20 „D" 1,5V. Ensure
that the polarity is correct.
• When a mains cable is connected the batteries are
automatically switched off.
• Close the battery compartment.
If you do not use the machine for a prolonged period,
remove the mains plug from the socket and remove the
batteries in order to prevent battery acid from leaking.
21.09.2004, 17:09:46 Uhr