Timer Playback - Pioneer X-HM10-K Manual De Instrucciones

Timer and sleep operation (Remote control only) (continued)
n Timer playback
Before setting timer:
l Check that the clock is set to the correct time (refer to
page 9). If it is not set, you cannot use the timer
function.
l For timer playback: Plug in USB or load discs or dock
iPod to be played.
1
Press the STANDBY/ON button to turn the power on.
2
Press and hold the CLOCK/TIMER button.
3
Within 30 seconds, press the
select "Once" or "Daily", and press the ENTER button.
4
Within 30 seconds, press the
select "Timer set", and press the ENTER button.
5
To select the timer playback source (CD, TUNER, USB,
iPod, LINE IN), press the
ENTER button.
When you select the tuner, select a station by pressing
the or button, and then press the ENTER
button. If a station has not been programmed, "No
Preset" will be displayed and timer setting will be
cancelled.
6
To adjust the day, press the
press the ENTER button.
7
Press the ENTER button to adjust the hour. Press the
or button and then press the ENTER button.
8
To adjust the minutes, press the
then press the ENTER button.
9
Set the time to finish as in steps 7 and 8 above.
10
Adjust the volume using the VOL (+ or –) button, and
then press the ENTER button. Do not turn the volume
up too high.
11
Press the STANDBY/ON button to enter the power
stand-by mode. The "TIMER" indicator lights up and
the unit is ready for timer playback.
12
When the preset time is reached, playback will start.
The volume will increase gradually until it reaches the
preset volume. The timer indicator will blink during

timer playback.

13
When the timer end time is reached, the system will
enter the power stand-by mode automatically.
or button to
or button to
or button. Press the
or button and then
or button and
En-22
Once timer:
The timer will be cancelled.
Daily timer:
The timer operates at the same time every day. It will
continue until the daily timer setting is cancelled.
Cancel the daily timer when it is not in use.
Notes:
l When performing timer playback using another unit
connected to the USB terminal, select "USB" or "LINE
IN" in step 5.
l This unit will turn on or enter the power stand-by mode
automatically. However, the connected unit will not turn
on or off. To stop the timer playback, follow step
"Cancelling the timer setting" of this page.
Checking the timer setting:
1
Turn the power on and press and hold down the
CLOCK/TIMER button.
2
Within 30 seconds, press the
"Once" or "Daily", and press the ENTER button.
3
Within 30 seconds, press the
"Timer Call", and press the ENTER button.
Cancelling the timer setting:
1
Turn the power on and press and hold down the
CLOCK/TIMER button.
2
Within 30 seconds, press the
"Once" or "Daily", and press the ENTER button.
3
Within 30 seconds, press the
"Timer Off", and press the ENTER button. Timer will be
cancelled (the setting will not be cancelled).
Reusing the memorised timer setting:
The timer setting will be memorised once it is entered. To
reuse the same setting, perform the following operations.
1
Turn the power on and press and hold down the
CLOCK/TIMER button.
2
Within 30 seconds, press the
"Once" or "Daily", and press the ENTER button.
3
Within 30 seconds, press the
"Timer On", and press the ENTER button.
4
Press the STANDBY/ON button to enter the power
stand-by mode.
Note:
The clock setting will reset if the power cord is pulled out
or when there is a blackout.
or button to select
or button to select
or button to select
or button to select
or button to select
or button to select