Mitsubishi Electric PEH-P400MYA Para El Instalador página 13

[Detailed setting]
[4] -1. CHANGE LANGUAGE setting
The language that appears on the dot display can be selected.
• Press the [ MENU] button to change the language.
1 Japanese (JP), 2 English (GB), 3 German (D), 4 Spanish (E), 5 Russian
(RU), 6 Italian (I), 7 Chinese (CH), 8 French (F)
[4] -2. Function limit
(1) Operation function limit setting (operation lock)
• To switch the setting, press the [
1 no1: Operation lock setting is made on all buttons other than the [
button.
2 no2: Operation lock setting is made on all buttons.
3 OFF (Initial setting value):
Operation lock setting is not made.
* To make the operation lock setting valid on the normal screen, it is necessary to
press buttons (Press and hold down the [FILTER] and [
the same time for two seconds.) on the normal screen after the above setting is
made.
(2) Use of automatic mode setting
When the remote controller is connected to the unit that has automatic operation
mode, the following settings can be made.
• To switch the setting, press the [
1 ON (Initial setting value):
The automatic mode is displayed when the operation mode is selected.
2 OFF:
The automatic mode is not displayed when the operation mode is selected.
(3) Temperature range limit setting
After this setting is made, the temperature can be changed within the set range.
• To switch the setting, press the [
1 LIMIT TEMP COOL MODE:
The temperature range can be changed on cooling/dry mode.
2 LIMIT TEMP HEAT MODE:
The temperature range can be changed on heating mode.
3 LIMIT TEMP AUTO MODE:
The temperature range can be changed on automatic mode.
4 OFF (initial setting): The temperature range limit is not active.
* When the setting, other than OFF, is made, the temperature range limit setting
on cooling, heating and automatic mode is made at the same time. However, the
range cannot be limited when the set temperature range has not changed.
• To increase or decrease the temperature, press the [
button.
• To switch the upper limit setting and the lower limit setting, press the [
button. The selected setting will flash and the temperature can be set.
• Settable range
Cooling/Dry mode: Lower limit: 19°C ~ 30°C
Heating mode: Lower limit: 17°C ~ 28°C
Automatic mode: Lower limit: 19°C ~ 28°C
(2) Unit Function Selection
Set the functions of each indoor unit from the remote controller, as required. The functions of each indoor unit can be selected only from the remote controller.
Set the functions by selecting the necessary items from Table 1 and Table 2. (Default settings are also shown below)
Table 1. Itemized functions of the entire refrigerant system (select unit number 00 to 15)
Function
Power failure Not available
automatic recovery Available
Indoor temperature Unit operating average
detection Set by unit's remote controller
Remote controller's internal sensor
LOSSNAY Not Supported
connectivity Supported (unit is not equipped with outdoor-air intake)
Supported (unit is equipped with outdoor-air intake)
Power voltage 240 V
220 V, 230 V
Table 2. Itemized functions of the indoor unit (select unit numbers 01 to 04 or AL)
Function
100 Hr
Filter sign
2500 Hr
No filter sign indicator
Operation
Fan operation
during thermo off
Stop
in heating
operation
Fan operation
Operation
during thermo off
in cooling Stop
operation
Note:
When the indoor unit functions were changed using the function selection after installation is complete, always indicate the set contents by entering
mark in the appropriate check field of Table 1 and Table 2.
ON/OFF] button.
ON/OFF]
ON/OFF] buttons at
ON/OFF] button.
ON/OFF] button.
TEMP ( ) or (
Upper limit: 30°C ~ 19°C
Upper limit: 28°C ~ 17°C
Upper limit: 28°C ~ 19°C
Settings
Settings
* The settable range varies depending on the unit to connect (Mr. Slim units, Free-
plan units, and intermediate temperature units)
[4] -3. Mode selection setting
(1) Remote controller main/sub setting
• To switch the setting, press the [
1 Main: The controller will be the main controller.
2 Sub: The controller will be the sub controller.
(2) Use of clock setting
• To switch the setting, press the [
1 ON: The clock function can be used.
2 OFF: The clock function cannot be used.
(3) Timer function setting
• To switch the setting, press the [
followings.).
1 WEEKLY TIMER (Initial setting value):
The weekly timer can be used.
2 AUTO OFF TIMER: The auto off timer can be used.
3 SIMPLE TIMER: The simple timer can be used.
4 TIMER MODE OFF: The timer mode cannot be used.
* When the use of clock setting is OFF, the "WEEKLY TIMER" cannot be used.
(4) Contact number setting for error situation
• To switch the setting, press the [
1 CALL OFF: The set contact numbers are not displayed in case of error.
2 CALL **** *** ****: The set contact numbers are displayed in case of error.
CALL_: The contact number can be set when the display is as shown
on the left.
• Setting the contact numbers
To set the contact numbers, follow the following procedures.
Move the flashing cursor to set numbers. Press the [
button to move the cursor to the right (left). Press the [
button to set the numbers.
[4] -4. Display change setting
(1) Temperature display °C/°F setting
• To switch the setting, press the [
1 °C: The temperature unit °C is used.
2 °F: The temperature unit °F is used.
(2) Suction air temperature display setting
• To switch the setting, press the [
)] 1 ON: The suction air temperature is displayed.
2 OFF: The suction air temperature is not displayed.
]
(3) Automatic cooling/heating display setting
• To switch the setting, press the [
1 ON: One of "Automatic cooling" and "Automatic heating" is displayed under the
automatic mode is running.
2 OFF: Only "Automatic" is displayed under the automatic mode.
Mode no. Setting no. Check
1
01
2
1
02 2
3
1
03 2
3
1
04
2
Mode no. Setting no. Check
1
07 2
3
3
25
2
1
27
2
ON/OFF] button.
ON/OFF] button.
ON/OFF] button (Choose one of the
ON/OFF] button.
TEMP. (
CLOCK (
ON/OFF] button.
ON/OFF] button.
ON/OFF] button.
Default settings
Remarks
Approx. 4-minute wait-period
after power is restored.
Default settings Remarks
When selecting fan operation
"Stop", set setting no. of Mode
no. "02" in Table 1 to "3". Be sure
to place the remote controller
inside the room to be air-condi-
tioned so that it can monitor the
room temperature.
) and ( )]
) and ( )]
or other
13