Troubleshooting - Maytag Crosley Magic Chef CBR1415AGW Guia Del Usuario

Estufa a gas
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Troubleshooting

For most concerns, try these first.
• Check if oven controls have been properly set.
• Check to be sure plug is securely inserted into receptacle.
• Check or re-set circuit breaker. Check or replace fuse.
• Check power supply.
Surface burner fails to light.
• Check to be sure unit is properly connected to power supply.
• Check for a blown circuit fuse or a tripped main circuit
breaker.
• Check to be sure ignitor is dry and clicking. Burner will not
light if ignitor is damaged, soiled or wet. If ignitor doesn't
click, turn control knob OFF.
The flame is uneven.
• Burner ports may be clogged.
Surface burner flame lifts off ports.
• Check to be sure a pan is sitting on the grate above.
Baking results are not as expected or differ from
previous oven.
• Check the oven temperature selected. Make sure oven is
preheated when recipe or directions recommend preheat.
• Make sure the oven vent has not been blocked. See page 20
for location.
• Check to make sure range is level.
• Temperatures often vary between a new oven and an old
one. As ovens age, the oven temperature often "drifts" and
may become hotter or cooler. See page 19 for instructions on
adjusting the oven temperature (select models). NOTE: It is
not recommended to adjust the temperature if only one or
two recipes are in question.
• Use correct pan. Dark pans produce dark browning. Shiny
pans produce light browning.
• Check rack positions and pan placement. Stagger pans
when using two racks. Allow 1-2 inches between pans and
oven wall.
• Check the use of foil in the oven. Never use foil to cover an
entire oven rack. Place a small piece of foil on the rack below
the pan to catch spillovers.
Food is not broiling properly or smokes excessively.
• Check oven rack positions. Food may be too close to flame.
• Aluminum foil was incorrectly used. Never line the broiler
insert with foil.
• Trim excess fat from meat before broiling.
• A soiled broiler pan was used.
• Preheat oven for 2-3 minutes before placing food in the
oven.
• Broil with the oven door closed.
Oven will not self-clean (select models).
• Check to make sure the cycle is not set for a delayed start.
See pages 15.
• Check if door is closed.
• Check if control is in Sabbath Mode. See page 18.
• Oven may be over 400° F. Oven temperature must be below
400° F to program a clean cycle.
Oven did not self-clean properly (select models).
• Longer cleaning time may be needed.
• Excessive spillovers, especially sugary and/or acidic foods,
were not removed prior to the self-clean cycle.
Oven door will not unlock after self-clean cycle
(select models).
• Oven interior is still hot. Allow about one hour for the oven
to cool after the completion of a self-clean cycle. The door
can be opened when "LOCK" is not displayed.
• The control and door may be locked. See pages 5 and 16 to
unlock.
Moisture collects on oven window or steam comes
from oven vent.
• This is normal when cooking foods high in moisture.
• Excessive moisture was used when cleaning the window.
There is a strong odor or light smoke when oven is
turned on.
• This is normal for a new range and will disappear after a few
uses. Initiating a clean cycle will "burn off" the odors more
quickly.
• Turning on a ventilation fan will help remove the smoke
and/or odor.
• Excessive food soils on the oven bottom. Use a self-clean
cycle.
Fault Codes (select models)
• BAKE or LOCK may flash rapidly in the display to alert you if
there is an error or a problem. If BAKE or LOCK appear in
the display, press the Cancel pad. If BAKE or LOCK continue
to flash, disconnect power to the appliance. Wait a few
minutes, and then reconnect power. If the flashing still
continues, disconnect power to the appliance and call an
authorized servicer.
• If the oven is heavily soiled, excessive flareups may result in
a fault code during cleaning. Press the CANCEL pad and
allow the oven to cool completely, wipe out excess soil, then
reset the clean cycle. If the fault code reappears, contact an
authorized servicer.
Noises may be heard.
• The oven makes several low level noises. You may hear the
oven relays as they go on and off. This is normal.
• As the oven heats and cools, you may hear sounds of metal
parts expanding and contracting. This is normal and will not
damage your appliance.
There are no beeps and no display.
• Control may be in Sabbath Mode. See page 18.
"SAb" flashing and then displayed continuously.
• Oven is in Sabbath Mode. To cancel, press and hold the
Clock pad for five seconds.
10

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido