Kicker ZX.4 Serie Manual Del Propietário página 2

FourChannelModel:
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Installation . . . as easy as 1, 2, 3
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The amplifier's
end-panel controls need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4" (10cm) of open ventilation for
the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four
holes using a 7/64" (3mm) bit and use the supplied #8 screws to mount the amplifier.
2. Wiring Disconnect the vehicle's battery to avoid an electrical short. Then connect the ground wire
to the amplifier. Make the ground wire short, 24" (60cm) or less, and connect it to a paint-and
corrosion-free solid-metal area of the vehicle's
chassis.
Use a twisted pair(s) of RCA (low-level)
interconnect cable to feed the audio signal to
the amplifier. If you are using only one pair of
RCA inputs, connect the RCA cable to the AMP
1 inputs. Push the fader button out, and all four
channels will work with a single pair of RCA
input cable. Push the fader button in, when
using two pairs of RCA input cables. Keep the
RCA cable away from factory wiring harnesses
and other power wiring. If you need to cross this
wiring, cross it at a 90 degree angle.
Only use speaker wire (high-level) inputs if
your source unit does not have RCA type outputs. If you are using only one pair of high-level inputs,
connect the speaker wire to the AMP 1 input. Push the fader button out, and all four channels will work
with a single high-level input cable. Push the fader button in, when using both sets of high-level inputs.
Install a fuse within 18" (45cm) of the battery and in-line with the power cable connected to your
amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it.
See the chart below for power and ground wire size, and fusing recommendations.
ModelZX200.4
3. Configuration The following diagrams show the most common configurations for your Kicker ZX
series amplifier.
Four Channel Operation (Stereo) These ZX amplifiers are capable of operating into a minimum
impedance of 2 ohms per channel in stereo operation. See Figure 2.
Bridged Operation (Mono) ZX.4 series amplifiers are capable of operating into a minimum
impedance of 4 ohms when in bridged operation. See Figure 3.
Stereo and Bridged Operation Simultaneously The ZX.4 series amplifiers are capable of operating
into a minimum impedance of 4 ohms bridged and 2 ohms per channel in stereo operation. See
Figure 4.
2
ZX.4SeriesAmplifier
Owner'sManual
ZX200.4
__________________________
Authorized Kicker Dealer:
__________________________
Purchase Date:
__________________________ ZX200.4
Amplifier Model Number:
__________________________
Amplifier Serial Number:
Use only one type of signal input to the amplifier,
either RCA Cable or Speaker Wire
Speaker Wire
(High-Level
killers trk7"on Top"
Output)
RCA Cable
(Low-Level)
AMP 1
+ - - +
OFF HI LO
HI-LEVEL
INPUT XOVER
BASS GAIN
AMP 1
Fader Button: Push in for
2 pairs of inputs, push out
for a single pair of inputs.
Left +
Speaker Wire
Left -
Speaker Wire
(High-Level Input)
Right -
(High-Level Input)
AMP 1
Right +
AMP 2
Fuse30A PowerGroundWire 8GA
ZX.4AMPLIFIER
Left Speaker AMP 2
- +
-
+
Right Speaker AMP 2
Figure 1
+
RCA Cable
(Low-Level)
AMP 2
RCA
INPUTS + - - +
OFF HI LO
L L
HI-LEVEL
XOVER INPUT
GAIN BASS
Mono Speaker AMP 1
FADER
R R AMP 2
ON OFF
Left +
Left -
Right -
Right +
Left Speaker AMP 1
-
+
Right Speaker AMP 1
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.
Left Speaker AMP 1
Minimum impedance of 2 ohms per channel in stereo operation
- +
-
+
24"
Or Less
(60cm)
Ground
Right Speaker AMP 1
Remote
Turn-On
(45cm)
18"
Or Less
+12V
Fuse
Battery
Mono Speaker AMP 2
Minimum impedance of 4 ohms when in bridged operation
-
+
-
24"
Or Less
(60cm)
Ground
Remote
Turn-On
(45cm)
18"
Or Less
+12V
Fuse
Battery
Mono Speaker AMP 2
Minimum impedance of 4 ohms when in bridged operation
and 2 ohms per channel in stereo operation
-
+
+
-
24"
Or Less
(60cm)
Ground
Remote
Turn-On
(45cm)
18"
Or Less
+12V
Fuse
Battery
Figure 2
Signal In AMP 2
Signal In AMP 1
Figure 3
Signal In AMP 2
Signal In AMP 1
Figure 4
Signal In AMP 2
Signal In AMP 1
3