Vimar Elvox ZD08 Manual Para El Conexionado Y El Uso página 13

9. Changing the backlight and LED behavior
1) Enter Programming Mode
2) Press "6" to enter Menu 6, the Mode LED will flash green.
3) Construct and enter a code using the following instructions: the first digit is 5, indicating the backlight and Led
option, the second digit is the option number for the backlight mode that you wish to select (see the following
table). The third and fourth digits are 0.
4) System returns to Transmit Mode, you will hear one beep, the Door LED will turn off and the Mode LED will
turn green.
WARNING: In modes 2 and 3, backlight is actually turned off or dimmed 10 seconds after programming.
Backlight and LED mode
LED active, backlight OFF
LED active, backlight ON (default)
LED and backlight OFF, both activated on any key press for ten seconds.
LED active / backlight Dimmed, backlight activated on any key press for
ten seconds.
10. Changing the Open Code
The Open Code is mainly used as a method to quickly test the Lock Strike Relay during installation.
The Default Factory Setting for the Open Code is 2580.
When the first user is added to the controller, the default Open Code will automatically be deleted, ready for a new Open
Code to be reentered.
1. Enter Programming Mode
2. Press "1" to enter Menu 1.The Mode LED will turn red.
3. Enter the new 4-digit code you wish to set as Open Code.
4. The ZD08 returns to Normal
Mode: the Door LED will turn off and the Mode LED will turn green.
NOTE
- Open Code does not function in Secure Mode.
- Wrong entries will return the controller to Normal Mode.
- Code 0000 will erase and deactivate the Open Code.
11. Changing the Auxiliary Code
The Auxiliary Code is mainly used as a method to quickly test the Auxiliary Relay during installation. The Default Fac-
tory Setting for the Auxiliary Code is 0852. When the first user is added to the controller, the default Auxiliary Code will
automatically be deleted, ready for a new Auxiliary Code to be re-entered.
1. Enter Programming Mode.
2. Press "2" to enter Menu 2. The Mode LED will turn orange.
3. Enter the new 4-digit code you wish to set as Auxiliary Code.
4. The ZD08 returns to Normal Mode: you will hear three beeps. The Door LED will turn off and the Mode LED will
turn green.
NOTE
- Auxiliary Code does not work in Secure Mode.
- Auxiliary Code only works when the Auxiliary Mode is 1 or 2.
- Code 0000 will erase and deactivate the Auxiliary Code.
12. Changing the Programming Code
1. Enter Programming Mode.
2. Press "3" to enter Menu 3: the Mode LED will turn green.
3. Enter the new 4-digit code you wish to set as Programming Code.
4. The ZD08 returns to Normal Mode: the Door LED will turn off and the Mode LED will turn green.
NOTE
- Programming Code can not be erased, i.e. the code 0000 is not valid and will not erase the Programming Code.
13. Changing the Normal / Secure Code
1. Enter Programming Mode
2. Press "4" to enter Menu 4: the Mode LED will flash red.
3. Enter the new 4-digit code you wish to set as Normal / Secure Code
4. The ZD08 returns to Normal Mode: The Door LED will turn off and the Mode LED will turn green.
NOTE
- When the Auxiliary Mode is 1, 2, 3, or 4 the Auxiliary Input takes priority over the Normal / Secure Code.
EN
Option number
0
1
2
3
Door
Mode
VERDE
Door
Mode
VERDE VERDE
0
?
5
Backlight
mode
Door
Mode
GREEN
Mode Door
RED GREEN
?
?
?
Door
Mode
GREEN
Mode Door
GREEN
Mode Door
ORANGE GREEN
?
?
?
Mode Door
GREEN
Mode Door
VERDE
Mode Door
VERDE
VERDE
?
? ?
Mode
Door
VERDE
Mode Door
VERDE
Mode
Door
ROSSO VERDE
? ?
?
Door
Mode
0
?
?
?
?
11