Bort BCT-170-M Instrucciones De Servicio página 6

English
GB
Die grinder
FR
INTENDED USE
This tool
is intended for high-precision grinding, sanding, cut-
ting, engraving, polishing and drilling in different materials
TECHNICAL SPECIFICATIONS
PRODUCT ELEMENTS
1. On/off switch
2. Spindle-lock button
3. Collet
4. Collet nut
5. Speed selection wheel
SAFETY
WARNING! Read all instructions. Failure to follow all instruc-
tions listed below may result in electric shock, fi re and/or
serious injury.
● This tool should not be used by people under the age of 16
years
● Only use this tool for applications without the use of water
● Always disconnect plug from power source before making
any adjustment or changing any accessory
ACCESSORIES
● SBM Group can assure fl awless functioning of the tool only
when original accessories are used
● Use only accessories recommended by SBM Group
● For mounting/using non-SBM Group accessories observe
the instructions of the manufacturer concerned
● Use only accessories with an allowable speed matching at
least the highest no-load speed of the tool
● Do not use damaged, deformed or vibrating accessories
● Handle and store grinding/cutting discs carefully to avoid
chipping and cracking
● Protect accessories from impact, shock and grease
● Never use grinding discs over 32 mm (1 1/4") Ø
● Never use drill bits over 3.2 mm (1/8") Ø
● Never use a cutting disc for side grinding
● Never use reducors or adaptors to fi t large-hole grinding/ cut-
ting discs
BEFORE USE
● Always check that the supply voltage is the same as the volt-
age indicated on the nameplate of the tool (tools with a rating
of 230V or 240V can also be connected to a 220V supply)
● Do not work with materials containing asbestos
● Clamp the workpiece in case it does not remain stationary
from its own weight
● Use completely unrolled and safe extension cords with a ca-
pacity of 16 Amps (UK 13 Amps)
● Wear protective glasses and gloves, hearing protection, a
dust mask, and sturdy shoes; when necessary, also wear an
apron
● Wear a dust protection mask when working with materials
which produce dust that is detrimental to health; inform your-
self beforehand about the materials to be worked on
● Ensure that the collet size corresponds with the shaft size of
the accessory
● Be sure tool is switched off when plugging in
6
1
2
DURING USE
● Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
● Never use tool when cord is damaged; have it replaced by a
qualifi ed person
● Never use spindle lock while tool is running (damage due to
improper handling will be excluded from the guarantee)
● Keep hands away from rotating accessories
● When grinding metal, sparks are generated; keep other per-
sons and combustible material from work area
● Keep ventilation slots uncovered
● In case of electrical or mechanical malfunction, immediately
switch off the tool and disconnect the plug
AFTER USE
● The accessory continues to rotate for a short time after the
tool has been switched off
● Before you put down the tool, switch off the motor and ensure
that all moving parts have come to a complete standstill
● After switching off the tool, never stop the rotation of the ac-
cessory by a force applied against it
● Store tool in locations where temperature will not exceed
50°C
WHEN CONNECTING NEW 3-PIN PLUG (U.K.
ONLY):
● Do not connect the blue (= neutral) or brown (= live) wire in
the cord of this tool to the earth terminal of the plug
● If for any reason the old plug is cut off the cord of this tool, it
must be disposed of safely and not left unattended
Your machine is double insulated in accordance with
EN 50144; therefore no earthwire is required.
MAINTENANCE
Make sure that the machine is not live when carrying
out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth, prefer-
ably after each use. Keep the ventilation slots free from dust and
dirt.If the dirt does not come off use a soft cloth moistened with
soapy water. Never use solvents such as petrol, alcohol, ammo-
nia water, etc. These solvents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please contact
your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during transport,
it is delivered in a sturdy packaging. Most of the packaging ma-
terials can be recycled. Take these materials to the appropriate
recycling locations. Take your unwanted machines to your local
SBM Group dealer. Here they will be disposed of in an environ-
mentally safe way.