Descargar Imprimir esta página

Using The Machine; Throttle Control Lever - Stiga BC 900 D Li 48 Manual De Instrucciones

Desbrozadora/cortadora de pasto portátil alimentada a batería
Ocultar thumbs Ver también para BC 900 D Li 48:

Publicidad

1. Insert the wrench supplied (Fig. 7.A) into
the appropriate hole on the transmission
and rotate the blade (Fig. 7.B) by hand
by pushing the wrench (Fig. 7.A) until
it engages in the hole of the angle
transmission and blocks its rotation.
2. Unscrew the nut (Fig. 7.E) and
remove the cup (Fig. 7.D).
3. Remove the outer ring nut (Fig. 7.C),
then remove the blade (Fig. 7.B).
4.4 FITTING THE BATTERY BACKPACK
The battery backpack is delivered already
assembled
(Fig.
1.J) and can be released from
the strap support (Fig. 8) and carried by hand.
To release the battery backpack, press
on the two upper buttons (Fig. 8.A).
The battery compartments are located on
both sides of the backpack (Fig. 9).
The following can be found on the
right side of the backpack:
• cable socket (Fig. 10.A)
• battery selector (Fig. 10.B)
• one USB port for charging other devices
(e.g. mobile phones) (Fig. 10.C)
To avoid any loose cables, there are
grooves on both sides and at the rear, in
which the power cable can be inserted.
5. CONTROLS

5.1 THROTTLE CONTROL LEVER

Used to start and regulate cutting means speed.
The throttle safety lever allows the throttle
control lever to be used (Fig. 11.A); this is
only possible if the throttle safety button is
pressed at the same time (Fig. 11.B).
The cutting means stops automatically
when the throttle safety lever is released.
5.2 THROTTLE SAFETY BUTTON
The throttle safety button (Fig. 11.B) allows the
throttle control lever to be used (Fig. 11.A).

6. USING THE MACHINE

DANGER
The safety regulations to be followed are
described in chapter 2. Strictly comply with these
instructions to avoid serious risks or hazards.
6.1 PRELIMINARY OPERATIONS
Before starting work
several checks and operations to ensure you
can work efficiently and in maximum safety:
1. place the machine in a stable
horizontal position on the ground;
2. choose the most suitable cutting means
for the job to be done (par. 4.3.1);
3. check the battery (par. 6.1.1);
4. Wear the battery backpack
correctly (par 6.1.2);
5. prepare the machine support (par. 6.1.3).
6.1.1 Checking the battery
The machine is supplied without the battery.
Purchase the battery with the capacity that
most suits your operational requirements
and fully charge it according to the
instructions in the battery charger manual.
The list of approved batteries for this machine
can be found in the "Technical Data" table.
Before each use:
• Check the battery charge status by
following the instructions provided
in the battery charger manual.
6.1.2 Using the battery backpack
1. Insert the battery in one of the compartments
of the battery backpack and push it
completely, until hearing the click that
signals its locking in position, ensuring
thus the electrical contact (Fig. 9).
2. Connect the cable to the specific socket
and rotate it until hearing the specific click
that signals its locking in position, ensuring
thus the electrical contact (Fig. 10.A).
3. Adjust the straps (Fig. 12.A).
4. Close the harness at the front (Fig. 12.B).
5. Connect the cable to the machine (Fig. 13).
6.1.3 Using the machine support
DANGER
Frequently check the efficiency of the
quick release (Fig. 12.C) to guarantee
EN - 12
it is necessary to carry out

Publicidad

loading

Este manual también es adecuado para:

Sbc 900 d ae