Operation - Craftsman 315.DD2010 Manual Del Operador

WARnInG:
Do not allow familiarity with tools to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious injury.
WARnInG:
Always wear eye protection marked to
comply with ANSI Z87.1. Failure to do so could result
in objects being thrown into your eyes resulting in
possible serious injury.
WARnInG:
Do not use any attachments or
accessories not recommended by the manufacturer of
this tool. The use of attachments or accessories not
recommended can result in serious personal injury.
APPLIcATIOnS
You may use this product for the purposes listed below:
 Drilling in all types of wood products (lumber, plywood,
paneling, composition board, and hard board)
 Drilling in ceramics, plastics, fiberglass, and laminates
 Drilling in metals
 Driving screws into wood and drywall with screwdriver
bits.
This product will accept Craftsman
battery packs and Craftsman 19.2 V nickel-cadmium
battery packs.
For complete charging instructions, refer to the Operator's
Manual for your battery pack and charger models.
BATTERY PROTEcTIOn FEATURES
Craftsman 19.2 V lithium-ion battery packs are designed
®
with features that protect the lithium-ion cells and
maximize battery life.
If the tool stops during use, release the trigger to reset
and resume operation. If the tool still does not work, the
battery needs to be recharged.
TO InSTALL BATTERY PAck
See Figure 2, page i.
 Lock the switch trigger by placing the direction of
rotation selector in the center position.
 Place battery pack in the tool. Align raised rib on
battery pack with groove inside tool.
 Make sure the latches on each side of the battery pack
snap into place and battery pack is secured in tool
before beginning operation.
NOTICE:
When placing battery pack in the tool, be
sure raised rib on battery pack aligns with groove
inside tool and latches snap into place properly.
Improper assembly of battery pack can cause
damage to internal components.

OPERATIOn

19.2 V lithium-ion
®
8 - English
WARnInG:
Always remove battery pack from
your tool when you are assembling parts, making
adjustments, cleaning, or when not in use. Removing
battery pack will prevent accidental starting that
could cause serious personal injury.
TO REMOVE BATTERY PAck
See Figure 2, page i.
 Lock the switch trigger by placing the direction of
rotation selector in the center position.
 Locate latches on end of battery pack and depress to
release battery pack from the tool.
 Remove battery pack.
:
WARnInG
Battery products are always in operating
condition. Therefore, the switch should always be
locked when not in use or carrying at your side.
SWITcH TRIGGER
See Figure 3, page i.
To turn the drill On, depress the switch trigger. To turn it
OFF, release the switch trigger.
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
with increased trigger pressure and lower speed with
decreased trigger pressure.
nOTE: You might hear a whistling or ringing noise from
the switch during use. Do not be concerned; this is a
normal part of the switch function.
DIREcTIOn OF ROTATIOn SELEcTOR
(FORWARD/REVERSE/cEnTER LOck)
See Figure 3, page i.
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With the drill
held in normal operating position, the direction of rotation
selector should be positioned to the left of the switch
trigger for forward drilling. The drilling direction is reversed
when the selector is to the right of the switch trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental starting when
not in use.
NOTICE:
To prevent gear damage, always allow the
chuck to come to a complete stop before changing
the direction of rotation.
To stop the drill, release the switch trigger and allow the
chuck to come to a complete stop.
nOTE: The drill will not run unless the direction of rotation
selector is pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage may
cause the drill to become overheated. If this occurs, cool
the drill by running it without a load and at full speed.