Phoenix Gold SX2 400.2 Manual De Instrucciones página 6

SX2 600.1
MONOBLOCK POWER AMPLIFIER
LINE IN
Connect preamp signal cables from the source unit to these
terminals.
LINE OUT
Used to connect multiple amplifiers without degrading
signal strength via internal line driver. Also utilized when
connecting amplifiers together in a Master/Slave
configuration (See Master/Slave).
BAL / UNBAL
Select Balanced or Unbalanced inputs based on your input
source's design for best S/N performance.
AUTO ON
Auto-on is useful when connecting to an OEM system
that does not offer a Remote turn-on lead to activate the
amplifier. When connecting directly to the amplifier using
a high-level input signal the circuit can detect the input
voltage (BTL <1v DC) and activate the amplifier. If your
system has a standard remote turn-on lead use the standard
REM input. If it is an OEM system that stays active even with
the radio off (voltage on signal wires) move the switch to
the OFF position and locate an alternative circuit or
L.O.C. PRO device to activate the amplifier.
Balanced/Unbalanced for High Level input wiring.
SX2 - 600.1
SX2 600.1
AUTO
UN BAL OFF MASTER
R
BAL ON SLAVE
LINE IN LINE OUT
40Hz EQ
Up to 6dB of bass boost @ 40Hz. Adjust this with the mindset
of less is more as usually only minor adjustments (if any) are
needed for most modern systems. Most systems will benefit
from proper Phase adjustment without having to use boost.
LP
Variable lowpass crossover frequency adjustment from
40Hz - 240Hz @ 24dB per octave.
REMOTE
Selecting LP activates this port. This port is for connecting
the (RBPC) remote bass level and phase controller with
BASS SHIFT . The unique feature of the RBPC with BASS
®
SHIFT® allows for perfect adjustment of not only the
subwoofer level but also 0-180° of phase adjustment from
the listening position. Properly adjusting phase will allow
enhanced bass response, dynamics and impact at any
volume. To adjust, play a test tone close to the crossover
overlap you have the system adjusted to, typically in the
50-100Hz range. With all system speakers playing and at
a moderate volume, slowly adjust the phase dial on the
RBPC across the entire range. When the subwoofer is in
© 2017 Phoenix Gold • www.phoenixgold.com
PAC
See Source
LP
36 125
20 70 80 185
13 90 55 215
10 120 0 180 0 +6 40 240
dB
HP PHASE 40Hz EQ LP
FLAT
MASTER / SLAVE
Select Master if single amplifier or not connecting multiple amplifiers
in either Strapped or Linked mode. Strapped mode will allow 2 SX2
600.1 amplifiers to be combined together as a single amp and
drive a 2Ω load in excess of 1200 watts. Linked mode will allow any
number of SX2 600.1 amplifiers to be connected to a Master SX2
600.1. Allowing all connected amplifier adjustments to be made via
the Master amplifier. See diagrams for correct wiring configurations.
LP/ FLAT
Select LP for subwoofer applications, will also activate REMOTE
input. Select FLAT for use with external processor or for full range
applications.
HP
HP adjusts a highpass crossover that can be used as a subsonic
filter. Use in conjunction with LP/ FLAT switch. If LP is selected, then
adjust HP dial to desired crossover point, variable from 10Hz - 120Hz
@ 24dB per octave. Typically used for vented subwoofer systems
and is adjusted to the port tuning frequency to prevent overdriving
of the subwoofer.
PHASE
Set to 180° on amplifier to allow adjustment from RBPC. The unique
feature of the RBPC with BASS SHIFT
of not only the subwoofer level but also 0-180° of phase adjustment
from the listening position. Properly adjusting phase will allow
enhanced bass response, dynamics and impact at any volume.
If not utilizing the RBPC, adjust phase directly from amplifier. See
RBPC instructions for proper adjustment.
-
PEAK
8v 0.3v
LEVEL SPEAKER
REMOTE
phase with the other speakers in the system, you should be able to
detect a rise in volume, "the sweet spot." Now return the control to
the sweet spot and make small adjustments +/- until you maximize
the output. You have now completed adjusting the phase and
should not have to adjust this again. Use the level control to adjust
the subwoofer output to your preference based on music program
material. NOTE: To allow adjustment from the RBPC controller, the
phase adjustment must be set to the 180° position on the amplifier.
PEAK
Peak output LED indicator. Helpful when used for subwoofer level
adjustment. Adjust LEVEL so PEAK LED flashes when driving amplifier
hard, but not so much that the LED stays on continuously. Light will
illuminate when rated output voltage is achieved.
FULL RANGE USE
SX2 Monoblocks are full range capable. Unlike traditional
monoblocks that are only used in bass applications, the SX2 600.1
can be configured for use as a powerful mono amplifier or used in
pairs to create an incredibly powerful stereo output. Applications
such as driving a large number of full range speakers with 600 watts
per channel or a strong component set with unlimited channel
separation with independent left and right amplifiers.
Amplifier Owner's Manual
BASS
allows for perfect adjustment
®
GND REM
RMD
SX2 600.1