Maintenance Instructions - EGT Chantilly Instrucciones De Instalación

ASSEMBLY INSTRUCTIONS
Warning ! Only for outdoor domestic use.
Madam, Sir,
This product has been designed and manufactured following requirements of 2009/48/EC European directive relating to safety of
toys. Compliance to these requirements has been checked by an independent laboratory, following safety of toys standard EN 71
part 1, 2, 3, and 8, and 1907/2006/CE regulation (REACH). All informations included in this instruction sheet are required by these
regulations. You must follow these to enable your children to use this product safely.
Assembly instructions
This product has to be assembled by yourself. You must keep this
instruction sheet for further use, most particularly for :
- Maintenance operations.
- Parts identi cation by our after sales service.
Do not throw packaging bags and boxes in nature. Follow recycling
instructions.
Following humidity rate of the air, wooden log diameter can increase
(very damp air) or decrease (very dry air), tolerance on linking angles
internal diameters take into account this phenomena.
Warning !
- Assembly must be done by an adult.
- Keep away children during assembly : choking hazard with small parts. - Keep away children during assembly : choking hazard with small parts.
- Every defective apparatus and/or part shall be only replaced by an
apparatus / part supplied by our after sales service or by an approved
retailer.
- Disregarding instructions detailed in this instruction sheet will involve
dangerous use of the product, with fall and/or shock hazard.
Before assembly, ensure that :
1 - The place where you build the product is :
- Plane and horizontal.
- Minimum 2 meters away from any object, structure or other
obstacle (hedge, tree, clothesline, electrical line...) that could hurt
product user.
- Not on a hard oor (concrete, asphalt...). Select grass or other kind
of soft oor (sand, shock absorbing materials...).
2 - Fastening is complete. You could have unused parts at the end of
the assembly, keep them for further use (spare parts).
When the product is equipped with a slide, we advise you to set it not directly facing the sun.
When the product is equipped with a slide, we advise you to set it not directly facing the sun.
After assembly :
- Fix the product on concrete anchors, realized by following instructions detailed on this instruction sheet.
NB : concrete blocks must be fully dry before xing the product on them. Only metal stake shall be drowned into concrete.
Not any part of the product shall be drowned into concrete.
- Clean every wood component from splinters that could appear during assembly, using sand paper.
- When needed, adjust apparatus setting (see gure Y).
- Check distance between apparatus bottom surface and the ground. Distances must be respected to enable a safe use of the product.
If they are below the speci cations indicated in gure W use teh plastic rings to adjust the height of the seat. If this is not possible, please contact our after
sales service.
Safety and use instructions
Warning ! This product is intended :
- For domestic use outside. It is not intended to be used in collective private use (hotel, resting place, camping, barracks, public building...), in collective
public use (school playground, public garden).
- To children from 3 to 12 years old, maximum weight 50 kg. Maximum weight is reduced to 35 kg per sitting place for double sit apparatus (see saw & double
swing).
If the product is equipped with a baby seat, it is only intended for children from 6 to 24 months, maximum weight 15 kg.
- Keep away from re
This toy must be used under adult supervision, who must make sure that :
- Children using the toy are old enough and have skills to use it.
- There is only one child per seat.
- There are no children in the swinging area of apparatus : shock hazard. There are no children that have a wron and/or dangerus use of the product : severe
injury hazard.

Maintenance instructions

To avoid any hazard by using the product, several points must be checked every month :
- Suspension hooks and hinge. Change them if wear is 10% more than original thickness.
- Structure and apparatus screws and nuts tightening : tighten again if necessary.
- Anchors resistance.
- Presence of nuts caps. Replace them by identical nuts cap if they are missing.
- Plastic part general condition. Replace them if they are cracked or drilled.
- Wear indicator : apparatus must be changed when metal part is visible on the plastic ring.
- Splinters on wooden parts. Clean them with sand paper if necessary.
- If the product is equipped with fabrics, they must be cleaned with a damp sponge. Do not use washing products.
To prevent the product for deteriorations due to weather conditions, remove and store all apparatus and accessories of the product during
winter period.
If corrosion occurs on metallic parts, clean them with a suitable product. If corrosion is still progressing, contact our after sales service.
Keep a watch on the oor where the product is installed, remove stones and all other object that could hurt users in case of falling.
Mon
Espace
SAV
AFTER SALES SERVICE AND INFORMATION ABOUT STANDARDS AFTER SALES SERVICE AND INFORMATION ABOUT STANDARDS
www.sav-egt-partners.com