3/4" Overlay Panel Dimensions - Monogram ZISB36 Manual De Instrucciones

Design Guide - Standard Installation
3/4" (1.91 cm) OVERLAY PANEL
DIMENSIONS
For a more custom appearance, overlay panels may
be installed on trimmed models. The overlay panel
must be secured to a 1/4" (0.63 cm) thick backer
panel which slides into the trim. A spacer panel 0.10"
(0.25 cm) thick must be placed between the overlay
and backer panel.
Assemble the panels with glue and screws:
• Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
• Center the spacer and backer panel on the overlay
panel and secure with glue and screws. Screws
must be countersunk into the backer panel.
IMPORTANT NOTE – DISPENSER MODELS
The refrigerator is supplied with two dispenser trims, one for framed panels and one for overlay panels. The
overlay dispenser trim is designed to fit a total panel thickness of 1.100".
• If the panel is less than 1.100" (2.79 cm) a noticeable gap may be created around the dispenser trim.
• If the panel is more than 1.100" (2.79 cm) the dispenser trim cannot be secured to the door.
See Dispenser Trim Fit Example, page 13.
• The overlay panel must be constructed according to the specifications shown to achieve the correct total
thickness.
• Alternative panel construction methods such as securing a 3/4" (1.91 cm) panel to a 1/4" (0.63 cm) backer
panel cannot be used. Another method, routing a 3/4" (1.91 cm) thick panel on all sides, cannot be used. These
methods will not result in the required 1.100" (2.79 cm) panel thickness.
A
Grille Panel
Dispenser
Cutout
G
F
Fresh Food
Freezer
Panel
Panel
E
D
31-1000450 Rev. 1
Dispenser Cutout
B
13-5/16"
11"
C 36" Side-by-Side (in inches)
1/4" Backer Panel
.10" Spacer Panel
3/4" Overlay Panel
42" Side-by-Side (in inches)
1/4" Backer Panel
.10" Spacer Panel
3/4" Overlay Panel
48" Side-by-Side (in inches)
1/4" Backer Panel
.10" Spacer Panel
3/4" Overlay Panel
Door
3/4"
Overlay
Panel
1/4"
.10"
Backer
Panel Spacer
.250" + .10" + .750" = 1.100" Total Panel Thickness
0.63 + 0.25 + 1.91 = 2.79 cm
*Cut the dispenser opening after the backer, spacer and overlay
panels have been assembled.
IMPORTANT NOTE: Maximum total weight for the
assembled panels:
•
Fresh food door panel – 75 lbs. (34.0 kg)
•
Freezer door panel – 53 lbs. (24.0 kg)
•
Grille Panel – 18 lbs. (8.16 kg)
A B C
33-7/8 9 68-3/8
33 8-3/8 67
34-1/8 9-1/4 68-5/8
A B C
39-7/8 9-1/2 68-3/8
39 8-5/8 67
40-1/8 9-3/4 68-5/8
A B C
45-7/8 9-1/2 68-3/8
45 8-5/8 67
46-1/8 9-3/4 68-5/8
11
Overlay Panel
Spacer Panel
Backer Panel
NOTE: Left-to-right offset
is not always equal to top-
to-bottom offset.
Dispenser Cutout
Position
D E F
14-9/16 18-9/16
13-1/4 17-1/4
14-13/16 18-13/16 34-5/16
D E F
14-9/16 24-9/16
13-1/4 23-1/4
14-13/16 24-13/16 34-5/16
D E F
18-9/16 26-9/16
17-1/4 25-1/4
18-13/16 26-13/16 34-5/16
G
2
G
2
G
4