Care And Cleaning - BLACK&DECKER BDWF7710 Manual De Instrucciones

Ventilador doble dígital con sensor rainsafe para ventana
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

BDWF7710Pub1000001430
10/11/04
4:51 PM
4. Temperature programming —
a) Press and hold the temperature control button for 3 seconds. Display blinks. "SET"
indicator in digital display is highlighted
b) Press the "+" or "-" adjustable thermostat buttons to select indoor temperature to turn
fan on. (Temp range: 65-90°F (18,3 °C a 32,2 °C ) )
c) Press the temperature control button to activate the
temperature mode. Display stops blinking.
ROOM temperature indicator is highlighted, displaying indoor temperature.
SET temperature indicator is highlighted, displaying indoor temperature set for fan
to start.
LED temperature indicator blinks red when actual indoor temperature is below set
temperature.
Note: Fan does not activate until set temperature is reached.
Press the temperature control button again to de-activate the temperature mode. LED
temperature indicator will not be illuminated.
5. Fans — Select speed setting for both fans. Press speed button:
Once for LOW
Twice for MED
Three times for HI
Fourth press of speed button turns the fan off.
Next press of button repeats the cycle.
Press the fan direction intake/exhaust button to exhaust. The speed when the button is
pressed remains the same.
Note: Fans shut off automatically once the set temperature is reached. If the unit does not
start, make sure that the "set temperature" is below the current room temperature. If the
fans are stopped and you want to turn them back on, lower the temperature setting until
you have reached the desired temperature. Press the temperature control button to
deactivate the temperature mode. To reactivate at the current temperature settings press the
temperature control button.
6. Rainsafe™ feature — only operates in the intake mode. When raindrops hit the
Rainsafe™ sensor on the back of the fan (A), unit turns off to prevent water from entering
the fan and being blown inside the room. Press the Rainsafe™ button to activate. LED
(red) illuminates continuously indicating activation. Detection by Rainsafe™ feature
automatically shuts off the fan. LED Rainsafe™ indicator blinks to show that the
Rainsafe™ sensor has turned off the fan. Fan automatically restarts after the water
evaporates.
Note: If the fan has shutoff due to the Rainsafe™ feature being activated, you can restart
the fan by pressing the Rainsafe™ button, therefore bypassing the Rainsafe™ function.
Press Rainsafe™ button a second time to deactivate the Rainsafe™ feature. LED
Rainsafe™ indicator will not be illuminated.
To Use with the Remote Control
The remote control (B) operates on 2 AAA batteries. Batteries are not included. Slide the
cover off the battery compartment on the back of the remote and install the batteries in the
orientation shown inside.
• The remote control (B) lets you operate the fan from a distance.
• When pushing buttons, be sure to direct the remote toward the remote control sensor on
the digital control panel. Make sure there is nothing obstructing the path.
• After use, place the remote control into the remote control storage area at the bottom,
front of fan.
For Use As A Floor Or Table Fan
Optional feet are included to enable the window fan to stand on its own. To attach the
optional feet, line up tab on back of foot with hole on back of fan base and snap front of
foot into place. Repeat procedure with other foot. Secure feet with screws (included).
Page 6
5

Care and Cleaning

This product contains no user serviceable parts. Refer service to qualified service
personnel. This fan is permanently lubricated and will not require additional lubrication for
the life of the fan.
Cleaning
1. Turn off fans and unplug.
2. Remove fan from window and detach any panel inserts from fan assembly.
3. Wipe off excess dust with a lint-free cloth. To ensure adequate air circulation, keep
vents dust free. A vacuum cleaner hose may be used to clean the vents.
4. DO NOT immerse the fan in water or any other liquid.
5. Be sure all parts of fan are completely dry before operating.
Storing
• Make sure to clean the fan before storing.
• Retain the original packaging for storing your fan.
• Always store fan in a dry place.
• Never store it while it is still plugged in.
• Never wrap the cord tightly around the fan, and do not put any stress on the cord
where it enters the fan, as it could cause the cord to fray and break.
6

Publicidad

Tabla de contenido
loading

Tabla de contenido