Revell Control TOXI Manual De Usuario página 8

• Always ensure that the charging
process takes place on a fireproof
surface in a fire-resistant environment.
• Do not leave the battery unsupervised
during the charging process.
• Never disassemble or alter the battery
contacts. Do not damage or puncture
the battery cells. There is a risk of
explosion!
• The LiPo battery must be kept out of
reach of children.
• When disposing of batteries, they
must be discharged or their capacity
must be fully depleted. Cover exposed
terminals with adhesive tape in order
to prevent short-circuiting!
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
1A Counter-rotating rotor blades
1B Stabiliser
1C Canopy
1D ON/OFF switch
2 REMOTE CONTROL
2A ON/OFF switch
2B Control for thrust
2C Left/right trim buttons
2D Power LED
2E Control for Forward/Reverse flight and
clockwise/anti-clockwise rotation
3 INSERTING BATTERIES (REMOTE CONTROL)
3A Unscrew and remove the cover.
3B Insert 4 x 1.5 V AA batteries and pay attention to the polarity,
as shown in the battery compartment.
3C Close the battery cover and secure with the screw.
14
Technical changes and differences in
color reserved!
Required batteries for the model:
Power supply:
Rated output:
1 x DC 3,7 V / 2,8 Wh
rechargeable
LiPo battery (included)
Capacity: 75 mAh
Battery requirement for the
remote control:
Power supply:
DC 6 V
Batteries:
4 x 1.5 V "AA"
(not included)
1 MODEL
1E Charging socket
1F Landing skids
1G LED
2F Locking screw for the battery
compartment
2G Battery compartment cover
2H Battery compartment
4 CHARGING THE MODEL
Attention: The battery and motor must cool down for 15 to 30 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
4A Carefully open the battery compartment.
4B Carefully remove the charging cable and connect to the charging socket 1E.
The plug should slide easily into the charging socket – DO NOT USE FORCE. If the
plug is not correctly inserted into the charging socket, the model can be damaged
and, under certain circumstances, cause injury.
4C Switch on the remote control. The Power LED on the remote control turns green as
soon as charging begins. The charging process is complete when the Power LED
turns red.
The model can fly for approx. 5-7 minutes after charging for approx. 30-35
minutes.
5 START PREPARATION
5A Press the ON/OFF switch 2A to switch on the remote control. The Power LED
2D flashes.
5B Move the ON/OFF switch 1D to ON. Place the model on a flat, solid base so
that its tail points toward you.
5C Then briefly move the control for thrust 2B forward and back again. After a few
seconds, the Power LED on the remote control becomes continuously red. Now the
helicopter is ready to start. After the flight, first switch off the helicopter, then the
remote control.
6 TRIM ADJUSTMENT OF THE CONTROL
Correct trimming is a basic requirement for the helicopter to fly perfectly. Its adjustment
is simple, but it requires some patience and a feel for it. Please observe the following
instructions precisely: Carefully move the thrust control up and raise the helicopter
approximately 0.5 to 1 metre in altitude.
6A
If the helicopter begins to auto-
matically rotate clockwise quickly
or slowly ...
If the model automatically rotates
clockwise quickly or slowly, tap the
left trim button 2C until the model
no longer rotates automatically.
6B
If the helicopter begins to auto-
matically rotate anti-clockwise
quickly or slowly ...
If the model automatically rotates
anti-clockwise quickly or slowly,
tap the right trim button 2C until
the helicopter no longer rotates
automatically.
15