Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
RADIOS AND ANTENNAS
The nMAP access point has two radios. Radio 1 is configured for
access point operation in 802.11b mode. Radio 2 is configured for
monitor operation in 802.11b/g mode. Connect four antennas, part
number 901167-2, to connectors J3, J4, J5, and J6 to enable
communication with wireless devices. The relationship between the
radios and external antennas are:
Radio Connector
Default
1
J4, J5, J6 Operating mode:
Access point
Wireless mode:
802.11b
2
J3
Operating mode:
Monitor
Wireless mode:
802.11b/g
* Choices may be limited by Country selected during setup.
ETHERNET PORTS
The nMAP access point has two auto sensing 10/100/1000 Base-T
Ethernet ports accessed via Quadrax connector J1.
RESET OPERATION
Reset lines are available in connector J2. Momentary connection
reboots the nMAP access point. Holding connection until
RF ENABLE indicator flashes green/yellow at one flash per second,
resets the nMAP to the factory default settings.
Radio Mode
Other Choices*
Operating Modes:
Local mesh
Access point and local mesh
Monitor
Wireless modes:
802.11a
802.11g
802.11b/g
802.11n (5 GHz)
802.11n/a
802.11n (2.4 GHz)
802.11n/g
802.11n/b/g
Operating Modes:
Access point
Local mesh
Access point and local mesh
Wireless Modes:
802.11a
802.11b
802.11g
DISCRETE INPUTS
Two discrete inputs accessed via connector J2 enable remote on/off
and RF on/RF off control.
DISCRETE OUTPUTS
Two discrete outputs provide remote indication when the nMAP
access point is powered up for operation and when RF is enabled.
INTERFACE CONNECTORS
Connector J1 provides connection for the two Ethernet ports:
Pin*
Signal
Quadrax Section A – 10/100/1000 Base-T Port 1 Primary
1
Bidirectional Pair A+
2
Bidirectional Pair B+
Quadrax Section B – 1000 Base-T Port 1 Secondary
1
Bidirectional Pair C+
2
Bidirectional Pair D+
Quadrax Section C – 10/100/1000 Base-T Port 2 Primary
1
Bidirectional Pair A+
2
Bidirectional Pair B+
Quadrax Section D – 1000 Base-T Port 2 Secondary
1
Bidirectional Pair C+
2
Bidirectional Pair D+
* Use ITT Cannon CA-140266-57 or equivalent mating connector.
Connector J2 provides connection for input power, discrete signals,
and IP address selection. (See nMAP Operator's Manual M365-627
for IP address selection wiring.)
Pin*
Signal
A
115 VAC Neutral
B
28 VDC Positive
C
28 VDC Return
D
Digital Ground
E
RF Status Output
F
Reset
G
IP_STRAP_1
H
IP_STRAP_2
J
No connection
*
Use M38999/26FD18SN for mating connector.
2
Pin*
Signal
3
Bidirectional Pair A-
4
Bidirectional Pair B-
3
Bidirectional Pair C-
4
Bidirectional Pair D-
3
Bidirectional Pair A-
4
Bidirectional Pair B-
3
Bidirectional Pair C-
4
Bidirectional Pair D-
Pin*
Signal
K
Chassis Ground
L
115 VAC Phase (hot)
M
No connection
N
No connection
P
On/Off Control
R
On/Off Status
S
IP_STRAP_0
T
No connection
U
RF Enable/Disable Control
Publicidad
Tabla de contenido
