Tripp-Lite AVR750U Guia De Inicio Rapido

system. For additional information, download the Owner's Manual PDF
Quick Installation
1
Plug the UPS into a properly grounded outlet: Please Note! The UPS
will not turn ON automatically in the presence of live utility power.
To Turn the UPS ON: Press and hold the "ON/OFF/MUTE/TEST" button
until you hear the system beep and then release the button. The system
is now turned ON.
To Mute the UPS: Quickly press the "ON/OFF/MUTE/TEST" button until you
hear a short chirp and then release the button. The system is now muted.
To Run a Self-Test: Press and hold the "ON/OFF/MUTE/TEST" button
until you hear a long, sustained beep and then release the button. The
system will now perform a self-test.
To Turn the UPS OFF: Press and hold the "ON/OFF/MUTE/TEST" button.
You will hear a short chirp, followed by a beep, then release the button.
The system is now turned OFF.
Basic Operation
ON/OFF/MUTE/ ON/OFF LED
TEST Button
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be
followed during the installation, operation and storage of all
Tripp Lite UPS Systems. Failure to heed these warnings may affect
your warranty.
UPS Location Warnings
• Install your UPS indoors, away from excess moisture or heat,
conductive contaminants, dust or direct sunlight.
• For best performance, keep the indoor temperature between
32º F and 104º F (0º C and 40º C).
• Leave adequate space around all sides of the UPS for proper
ventilation.
UPS Connection Warnings
• Connect your UPS directly to a properly grounded AC power
outlet. Do not plug the UPS into itself; this will damage the UPS.
• Do not modify the UPS's plug, and do not use an adapter that
would eliminate the UPS's ground connection.
• Do not use extension cords to connect the UPS to an AC outlet.
• If the UPS receives power from a motor-powered AC generator, the
generator must provide clean, filtered, computer-grade output.
Equipment Connection Warnings
• Use of this equipment in life support applications where failure
of this equipment can reasonably be expected to cause the
failure of the life support equipment or to significantly affect its
safety or effectiveness is not recommended. Do not use this
equipment in the presence of a flammable anesthetic mixture
with air, oxygen or nitrous oxide.
• Do not connect surge suppressors or extension cords to the
output of your UPS. This might damage the UPS and may affect
the surge suppressor and UPS warranties.
Battery Warnings
• Your UPS does not require routine maintenance. Do not open your
UPS for any reason. There are no user-serviceable parts inside.
201203043 933174-EN.indd 1
Quick Start Guide
AVR750U
Not suitable for mobile applications.
This document explains the most important features of your UPS
(in English or Spanish) from www.tripplite.com/support/manuals
OVERLOAD/CHECK Battery Backup/
BATTERY LED Surge Protected
• Batteries can present a risk of electrical shock and burn from
high short-circuit current. Observe proper precautions. Do
not dispose of the batteries in a fire. Do not open the UPS or
batteries. Do not short or bridge the battery terminals with any
object. Unplug and turn off the UPS before performing battery
replacement. Use tools with insulated handles. There are no
user-serviceable parts inside the UPS. Battery replacement
should be performed only by authorized service personnel using
the same number and type of batteries (Sealed Lead-Acid). The
batteries are recyclable. Refer to your local codes for disposal
requirements or visit www.tripplite.com/UPSbatteryrecycling for
recycling information. Tripp Lite offers a complete line of UPS
System Replacement Battery Cartridges (R.B.C.).Visit Tripp Lite
on the Web at www.tripplite.com/support/battery/index.cfm to
locate the specific replacement battery for your UPS.
• Do not attempt to add external batteries to the UPS.
FCC Notice, Class B
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Copyright © 2012 Tripp Lite. All rights reserved.
2
Plug your equipment into the UPS: Select outlets (see diagram) will
provide battery backup and surge protection; plug your computer, monitor
and other critical devices here.* Select outlets (see diagram) will provide
surge protection only; plug your printer and other non-essential devices here.
Note: UPS system will function properly upon initial startup; however,
maximum runtime for the unit's battery will only be accessible after it has
been charged for 24 hours.
* Your UPS is designed to support electronic equipment only. You will overload the UPS if
the total VA ratings for all the equipment you connect to the Battery Backup Protected/Surge
Protected outlets exceeds the UPS's Output Capacity. To find your equipment's VA ratings, look
on their nameplates. If the equipment is listed in amps, multiply the number of amps by 120 to
determine VA. (Example: 1 amp × 120 = 120 VA). If you are unsure if you have overloaded the
Battery Backup Protected/Surge Protected outlets, run a self-test.
Surge-Only
Protected
Outlets Outlets
1111 W. 35th Street,
Chicago, IL 60609 USA
www.tripplite.com/support
Tel/DSL Jacks USB Port
with Built-In
Splitter
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this equipment not expressly
approved by Tripp Lite could void the user's authority to operate
this equipment.
FCC Part 68 Notice (United States Only)
If your Modem/Fax Protection causes harm to the telephone
network, the telephone company may temporarily discontinue your
service. If possible, they will notify you in advance. If advance notice
isn't practical, you will be notified as soon as possible. You will be
advised of your right to file a complaint with the FCC. Your telephone
company may make changes in its facilities, equipment, operations or
procedures that could affect the proper operation of your equipment.
If it does, you will be given advance notice to give you an opportunity
to maintain uninterrupted service. If you experience trouble with this
equipment's Modem/Fax Protection, please visit www.tripplite.com/
support for repair/warranty information. The telephone company
may ask you to disconnect this equipment from the network until
the problem has been corrected or you are sure the equipment is
not malfunctioning. There are no repairs that can be made by the
customer to the Modem/Fax Protection. This equipment may not be
used on coin service provided by the telephone company. Connection
to party lines is subject to state tariffs. (Contact your state public utility
commission or corporation commission for information.)
Tripp Lite follows a policy of continuous improvement. Product
specifications are subject to change without notice.
Ground
Connection*
201203043 • 933174-EN
3/15/2012 12:17:39 PM