Safety Precautions - 3M 28366 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 28

Safety Precautions

1. Read all instructions before using this tool. All operators must be fully
trained in its use and aware of these safety rules.
2. The tool RPM should be checked on a regular basis to ensure proper
operating speed.
3. Make sure the tool is disconnected from the air supply.
4. Always wear required safety equipment when using this tool.
5. Always remove the air supply to the tool before fitting, adjusting or
removing the abrasive.
6. Always adopt a firm footing and grip and be aware of torque reaction
developed by the tool.
7. Use only 3M approved spare parts.
8. Always ensure the material being worked is firmly fixed to avoid
movement.
9. Check hose and fittings regularly for wear. Do not carry the tool by its
hose; always be careful to prevent the tool from being started when
carrying the tool with the air supply connected.
10. Dust can be highly combustible.
11. If tool is serviced or rebuilt, check to ensure that the maximum tool
RPM is not exceeded and that there is no excessive tool vibration.
12. Do not exceed maximum recommended air pressure. Use safety
equipment as recommended.
13. The tool is not electrically insulated. Do not use where there is a pos-
sibility of contact with live electricity, gas pipes, and/or water pipes.
14. This tool is not protected against hazards inherent in grinding and
cutting operations and no such accessories should ever be attached.
15. Take care to avoid entanglement with the moving parts of the tool
with clothing, ties, hair, cleaning rags or loose hanging objects. If
entangled, stop air supply immediately to avoid contact with moving
tool parts.
16. If the tool appears to malfunction, remove from use immediately and
arrange for service and repair.
17. Immediately release the start handle in the event of any disruption
of pressure; do not attempt to re-start until the disruption has been
corrected.
18. When tool is not in use, store in a clean dry environment free of
debris.
19. Recycle or dispose of tool according to Local, State, and Federal
Regulations.
at or near Tool
3M
1
/
in. to
3
/
in. File Belt Sander
8
4
REVISED 05/26/09
To Tool Station
Drain Valve
To Coupler
3M Contact Arms are perfectly mated for use on the
3M File Belt Sander. Constructed from premium, industrial-quality
materials, their durability and precise construction are the ideal
complement to the performance of the 3M File Belt Sander. The following
chart is a sample of products offered.
IT
P/N
See 3M ASD Accessory catalog 61-5002-8098-9 for additional
1
XPA2394 RETAINING COMPOUND
Accessories.
2
XPA2240 WHEEL POSITION BLOCK
3
XPA2239 SHAFT REMOVAL TOOL
4
XPA2238 BEARING REMOVAL TOOL 3/8 ID
5
XPA2237 BEARING REMOVAL TOOL 1/4 ID
6
XPA2236 BEARING MOUNT TOOL
7
XPA2447 BEARING REMOVAL TOOL 5/8 ID
Service Tool Kit
ITEM
1
RETAINING COMPOUND
2
WHEEL POSITION BLOCK
3
SHAFT REMOVAL TOOL
4
BEARING REMOVAL TOOL
5
BEARING REMOVAL TOOL
6
BEARING MOUNT TOOL
7
BEARING TOOL
Sloped in the direction of air flow
Drain Leg
Ball Valve
Filter
Ball
Regulator
Valve
Lubricator
Ball Valve
Air Hose
Air Compressor
and Tank
5
3M™ File Belt Contact Arms
DESCRIPTION
Service Tool Kit
Description
1
2
3
DESCRIPTION
3
/
ID
8 in.
1
/
ID
4 in.
5
/
ID
8 in.
Closed Loop Pipe System
Air Flow
Air Dryer
Figure 1
QTY.
Part Number
30670
4
7
5
6
QTY.
1
1
1
1
1
1
1
Revision 022514
R
1
A
1
1
B
1
1
1
1
X'
THE INFO
PROPER
DUCTIO
PERMISS
MATER
STD TO
.X
.X
DRWN B
1
TITLE
P/N
X

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

283712837328368283692837028372 ... Mostrar todo

Tabla de contenido