Soundcast VG10 Manual Del Usuario página 5

Capacitive Touch Keypad
The VG10 features an advanced capacitive touch key-
pad and backlighting technology. User functions are
accessed by a single press or press and hold over the
appropriate button area of the keypad
surface as indicated.
Powering On/Off: The VG10 is turned on and off us-
ing the large button located in the center of the keypad
Turn On: Press and hold the power button for (2) sec-
onds until the backlights illuminate and then release
within (2) seconds, a confirmation beep will confirm
unit is turned on
Turn Off: Press and hold the power button for (2) sec-
onds then release within (2) seconds, a confirmation
beep will confirm unit is turning off
Control Panel Keypad
Yellow AUX
Blue and orange LEDs
indicator
indicate current
LED
TWS state
TWS button
Bluetooth
button
Bluetooth
indicator LED
Eleven
LEDs for
volume and
fuel guage
display
Volume
Orange
down
power
button
LED
Connecting and Pairing
*The VG10 power must be turned on before trying to
pair (as well as aux input disconnected)
Bluetooth pairing with NFC
1. Enable Bluetooth and NFC functions on
your mobile device
2. Hold phone near the NFC logo (logo) on VG10 unit
until mobile device connects and Bluetooth
LED blinks slowly
3. Press OK/Connect on your mobile device
to complete pairing
4. Play audio
Standard Bluetooth Pairing
1. Enable Bluetooth on your mobile device
2. Pair a new device: press the VG10 Bluetooth
button (Bluetooth LED will blink slowly)
3. From Bluetooth menu on mobile device settings,
select "VG10 by Soundcast_xxxxxx"
4. Once paired, the Bluetooth LED becomes solid blue
➤ Press & Hold Bluetooth button for (2) seconds and
beep is heard to re-enter pairing mode to pair a new or
additional device.
➤ To clear all devices from memory, press and hold
the Bluetooth button for (10) seconds until the Blue-
tooth LED double blinks and second confirmation beep
Mute indicator
is heard.
Mute button
Aux Input Mode
Plug external audio source into 3.5mm jack to
Play/
automatically switch to Aux Input mode as indicated by
Pause
Aux LED turns yellow. Remove 3.5mm plug to switch
button
back to Bluetooth operation.
Power
button
TrueWireless Stereo (TWS) Pairing
With TWS, two VG10 units may be paired for synchro-
Volume nous Bluetooth playback. Power off, volume and TWS
up
mode will by synchronized and may be controlled from
button
either unit.
1. Both speakers must be powered on in Bluetooth
mode (no Aux input connected)
2. At least one of the speakers must be paired to
audio source (as described above)
Press and hold the TWS (TWS icon) for (2) seconds
until a confirmation beep is heard. The TWS LED will
start to blink slowly. Repeat with the second VG10
unit.
3. When paired, the TWS LED on both units will show
both blue and orange (purple)
➤ When in TWS mode and you turn off one unit, the
other unit will turn off automatically
4. Reconnecting: The TWS-paired units will re-con-
nect to each other automatically after turning both
units on. A short press of the TWS button on either
unit allows cycling through the TWS modes (stereo,
left/right, off) as indicated below;
• LED blue and orange: left/right
from each speaker
• LED orange only: left from primary
speaker, right from secondary speaker
• LED off: TWS off
➤ To clear all devices from TWS memory and return
to single device operation, press and hold the TWS
button for (10) seconds until third beep is heard and
the TWS LED double blinks, then turn the unit off.
When unit is turned on again, the TWS LED will not be
on, indicating that TWS is disabled.
➤ If you experience any difficulty with either standard
Bluetooth pairing or TWS operation, the VG10 Blue-
tooth system can be reset by clearing pairing memory
of both Bluetooth and TWS by using the (10) second
press and hold function (third beep) of each button and
then power cycling the unit.
➤ No music or intermittent dropouts? VG10 primary
and secondary units may be too far away
from each other.
Other Controls and Features
Volume Control:
The VG10 volume can be adjusted when playing music
or during speakerphone operation by pressing or
press and holding the + (up) or – (down) volume ad-
justment buttons on the keypad. The current volume
5