Connecting To A Wireless Network - Soundcast VG10 Manual Del Usuario

3. Follow the Play-Fi app instructions
4. After entering your router password; the app
will connect your device to your network. You will
notice the Wi-Fi Status light will have changed from
blinking to solid. This may take up to a minute. If,
after a minute, the button continues to blink rapidly,
setup failed and you should try again
5. Your wireless product is now connected to
your wireless network
6. Reconnect your mobile device to your wireless
network. You may rename your device using the app
iOS Device Users:
Please note: When using an iOS device your wireless
product can stream audio using either
Apple AirPlay or DTS Play-Fi.
1. Make sure your iOS device's Wi-Fi is turned on
and connected to your Wi-Fi network
2. Open your iOS device's 'Settings' app and go to
the 'Wi-Fi' menu. Your wireless product will show up
under the heading 'SETUP NEW AirPlay SPEAKER ... '
3. Select your wireless product from the list. It will
have "Play-Fi " in the name
4. Once in the 'AirPlay Setup' menu you will be
prompted to select your Wi-Fi network and name
your speaker (you will not need to enter your
network password)
5. Once your device is connected, you will notice that
the Wi-Fi Status light on your wireless product will
change from blinking to solid. This may take up to a
minute. If, after a minute, the button continues to
blink rapidly, setup failed and you should try again.
6. Your wireless product is now connected to your
wireless network. Reconnect your iOS device to your
wireless network.
PC Users:
1. Launch the Play-Fi app (located in the
Windows task bar)
2. The app will automatically find your device and
provide prompts for set up. If the app does not
prompt you to set up a new device, within the app go
to the settings screen and click 'Setup Play-Fi Device'
3. Follow the onscreen instructions
4. Click the "Set-up" button on the screen
5. Select the speaker(s) you want to set up
6. Enter the password for your wireless network;
the app will connect your device to your network. You
will notice the Wi-Fi Status light will have changed
from blinking to solid. This may take up to a minute. If,
after a minute, the button continues to blink rapidly,
setup failed and you should try again.
7. Your VG10 is now connected to your wireless
network. If necessary, reconnect your PC to
your wireless network
8. You may re-name your VG10 and perform
other functions using the Play-Fi app

Connecting to a Wireless Network:

Wi-Fi Protected Setup (WPS)
Wi-Fi Protected Setup (WPS) is a feature found
on most wireless routers that allows your wireless
product to securely and automatically connect without
needing to enter a password. WPS is not a standard
feature on all routers, and only one wireless product
can be set up at a time.
Check your router's owner's manual to see if WPS is
an available feature, or look for a button on your router
marked with the WPS logo (t~). If your router does not
have WPS, then use Access Point Wireless Setup.
1. For optimal setup conditions place your VG10 next
to your wireless router. The device can be moved to
its final location after Wi-Fi setup.
2. Plug in your wireless product and press the Power
button. The Wi-Fi Status light will start rapidly blink-
ing for about 20 seconds while your wireless product
is booting up. If your wireless product is not configured
to connect to your network, it will continue to blink.
If this is the first time your new wireless product i
plugged in, the Wi-Fi Status light will start pulsing
slowly. If the wireless product is already configured
to connect to a Wi-Fi network, the Status Light will
turn solid (connected) or blink rapidly (not connect-
ed).
3. To initiate Wi-Fi Protected Setup (WPS), for 3
seconds, press and hold the Wireless Setup button
on the back of your wireless product until you hear a
tone. The Wi-Fi Status light will blink twice in continu-
ous\ intervals to indicate WPS mode. Now push the
WPS button (t~) on your router. If you cannot find a
WPS button on your router, refer to the router's
owner's manual.
4. Once the Wi-Fi Status light turns solid (not
blinking), this indicates your VG10 is connected to
your wireless network. If, after a minute, the button
continues to blink rapidly, setup failed and you should
try again.
5. Connect your mobile device or PC to the same
network as your wireless product. Launch the DTS
Play-Fi app. Upon launching, it will automatically
detect your wireless product and should prompt you to
name your wireless product.
Restore to Factory Operation:
1. Speaker in power on mode, switch source to
AUX(plug analog input),
adjust volume to MAX, then MUTE speaker
2. Long press TWS button more than 10sec to set
up reset.
3. speaker will reboot automatically and forget
network.
9