LEGRAND Wattstopper MDW-101 Manual De Instrucciones página 2

The illustrations below show examples of free-topology wiring. The LMDW communicates to all other Digital Lighting Management
devices connected to the low voltage DLM Local Network, regardless of their position on the DLM Local Network.
LMDW-102
Switch/Sensor
DLM Local Network
Low Voltage
LMRJ Cables
Daylight Sensor
Each load is automatically assigned to a switch button.
• If there is only one load it will default to Manual ON/Auto OFF. If there is more than one load then the first load will default to Auto
ON/Auto OFF and the rest of the loads will default to Manual ON/Auto OFF.
• If there are more buttons on a switch than there are loads, the extra button(s) do nothing and blink when pressed.
• If there are fewer buttons on a switch than there are loads, the last button controls all remaining loads.
Load Selection Procedure
A configuration button allows access to our patented Push n' Learn™ technology to change the binding relationship between switch
buttons and loads.
Step 1 Enter Push n' Learn
Using a pointed tool, press and hold the configuration button for 3 seconds, until the Red LED on the switch begins to blink.
When you release the switch's configuration button, the red LED on other communicating DLM Local Network devices begins to blink.
The DLM Local Network is now in PnL mode. The Red LEDs continue to blink until you exit PnL mode.
All loads in the room turn OFF after entering PnL. After one second, one load turns ON. This is Load #1, which is bound to switch button #1 as
part of the Plug n' Go factory default setting. The Blue LED will be ON for all switch buttons and sensors that are bound to this load.
Step 2 Load selection
Press and release the configuration button to step through the loads connected to the DLM Local Network. As each load turns ON note
which devices (switch buttons and sensors) are showing the blue LED. These devices are currently bound to the load that is ON.
To unbind a switch button from a load, press the switch button while its blue LED is ON. The blue LED turns OFF to indicate the button
no longer controls the load that is currently ON. Use the up and down arrow to bind and unbind the sensor.
Pressing the switch button again while the load is ON rebinds the load to the button and the blue LED illuminates.
Step 3 Exit Push n' Learn
Press and hold the configuration button until the red LED turns off, approximately 3 seconds.
Occupancy Sensor parameters can be modified directly on the LMDW, or by using LMCS-100 software or the LMSM Segment Manager
interface. To modify the parameters directly on the LMDW, remove the lens to expose a display, then use a small screwdriver or
paper clip to navigate through the menus with the Feature and Configure
buttons and change values with the Yes and No buttons. (See Buttons and
Indicators on the first page.) Details on the various screens are found in the
DLM System Guide. Once programming is complete, reinsert the lens.
Releasing the Lens
Insert a small paper clip into the small hole at the top of the trim ring. Press in
firmly until the lens is released and springs forward. Grab the lens and remove
it completely to expose the screen.
Line
Voltage
Line/Hot Neutral
Black wire White wire
LMRC
102
Room
Controller
Yellow wire
to Load B (2)
Red wire
J-Box to Load A (1)
CAUTION: TO CONNECT A COMPUTER TO THE DLM LOCAL NETWORK USE THE
LMCI-100. NEVER CONNECT THE DLM LOCAL NETWORK TO AN ETHERNET
PORT – IT MAY DAMAGE COMPUTERS AND OTHER CONNECTED EQUIPMENT.
PLUG N' GO OPERATION (PNG)
UNIT ADJUSTMENT - PUSH N' LEARN (PNL)
MODIFYING SENSOR PARAMETERS
CONNECTIVITY
Loads
1
2
2
DLM Local Network
(low voltage, Class 2)
LMRJ Cables
Corner Mount
Occupancy
Sensor
Room
Controller
J Box
To
Load/Line
(Class 1 wiring)
LMDW
Sensor/
Switch
LCD
Display