Specific Safety Rules; Residual Risks - Ryobi OLT1825 Traducción De Las Instrucciones Originales

BATTERY TOOL USE AND CARE
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
When battery pack is not in use, keep it away from
other metal objects like, paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.

SPECIFIC SAFETY RULES

WARNING
When using the product, the safety rules must be
followed. For your own safety and that of bystanders,
please read these instructions before operating the
product. Please keep the instructions safe for later use.
WARNING
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
Stop machine if anyone enters the area. Never operate
the machine while people, especially children, or
pets are nearby. If you are approached, stop the unit
immediately.
Avoid using machine in bad weather, especially if there
is risk of lightning.
Use the product in daylight or good artificial light.
Avoid using on wet grass.
Keep proper footing and balance at all times.
Do not walk backwards when trimming.
Walk, never run.
Keep the trimmer head below waist level.
2
Do not cut on surfaces other than grass on ground.
Never operate the product with damaged guards or
without guards in place.
Never fit a metal replacement line.
Keep hands and feet away from the cutting means at
all times and especially when switching on the motor.
Thoroughly inspect the area where the machine is to be
used and remove all rocks, sticks, metal, wire, bones,
toys, or other foreign objects.
Switch off and disconnect from the power supply before:
servicing
–
leaving the trimmer unattended
–
cleaning your trimmer
–
changing accessories
–
checking for any damage after hitting an object
–
checking for any damage if the trimmer starts to
–
vibrate abnormally
performing maintenance
–
Wear protective glasses or goggles.
Take care against injury from any device fitted for
trimming the filament line length.
MAINTENANCE
Use only genuine replacement parts and accessories.
After extending new cutter line, always return the
product to its normal operating position before switching
on.
After each use, clean with a soft dry cloth.
Check all nuts, bolts and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorized service
centre.
When not in use, the product should be stored in a cool
dry place and locked up out of the reach of children. Do
not store outdoors.
Inspection after dropping or other impacts
Thoroughly inspect the product and identify any affections
or damage with it. Any part that is damaged should be
properly repaired or replaced by an authorized service
centre.

RESIDUAL RISKS

It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fingers, usually apparent
upon exposure to cold.
Hereditary factors, exposure to cold and dampness, diet,
smoking and work practices are all thought to contribute to
the development of these symptoms. There are measures
that can be taken by the operator to possibly reduce the
effects of vibration:
Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
English