Publicidad
Idiomas disponibles
Idiomas disponibles
c04
Sensor sig-
1= 4-20mA
nal type
2= 0-20mA
c05
Initial scale
Pressure:
value of the
0 to 60 bar
sensor. Only
Tempera-
if sensor is
ture:
used.
-20 to 100°C
Level:
0 to 50 m
r05
Calibration
0= Disabled
of the initial
1= Enabled
scale in mA.
t05
Software
Standard
filter for ana-
Lowara
logue input
c06
Full scale
Pressure:
value of the
0 to 60 bar
selected
Tempera-
sensor. Only
ture:
if sensor is
-20 to 100°C
used.
Level:
0 to 50 m
THRESHOLD AND TIMING (threshold is active
only with sensor)
c07
Unique level
0= Disabled
set point
1= Enabled
r07
Set point
0 to Full
level value
Scale
r08
Upper
0 to Full
threshold
Scale
delta
r09
Lower
0 to Full
threshold
Scale
delta
r10
Threshold
0
Start Pump 1
Scale
t10
Delay time
0 to 100
start Pump 1
r11
Threshold
0
Stop Pump 1
Scale
t11
Delay time
0 to 100
stop Pump 1
r12
Threshold
0
Start Pump 2
Scale
t12
Delay time
0 to 100
start Pump 2
r13
Threshold
0
Stop Pump 2
Scale
t13
Delay time
0 to 100
stop Pump 2
COMBINATION (refer to section
tion)
c14
Enable
0= only G1
combina-
and G2
tions of
1= only G
stopping
MIN and S
and/or start-
MIN con-
ing the
nected (float
pumps by
switch or
the float
probe S MIN
-
1
vari-
0
ous
-
0
-
3
Vari-
10.0
ous
-
0
Vari-
5
ous
Vari-
0.5
ous
Vari-
0.5
ous
to
Full
Vari-
8
ous
sec
2
to
Full
Vari-
2
ous
sec
0
to
Full
Vari-
7
ous
sec
2
to
Full
Vari-
1
ous
sec
0
6.2
for descrip-
-
3
switches (G)
+ common S
and probes
COM probe)
(S).
2= only G
MAX and S
MAX con-
nected (float
switch or
probe S
MAX +
common S
COM probe)
3= G MIN/S
MIN and G
MAX /S
MAX
STARTING PUMP ROTATION
c15
Enable
0= Disabled
pump rota-
1= Enabled
tion. Auto-
matic pump
rotation
takes place
each time
the set is
restarted
after stop-
ping in au-
tomatic
mode. If
cyclic ex-
change of
the pumps is
disabled, the
floats or
probes must
be connect-
ed to their
relative
pumps: P1-
G1 (or S1),
P2-G2 (or
S2).
This function
is essential
when the
pumps are
located at
different
stations.
c16
Insert the
1= Pump 1
duty pump
2= Pump 2
that you
want to start
first after
powering up
or after re-
set.
Parameter
c15 must be
in ENA-
BLED mode
c17
If automatic
0= Disabled
pump rota-
1
en - Original instructions
-
1
-
1
Hour
0
to
12
s
41
Publicidad
