Settings; Setting Up The Receiver; Activating The Network Standby Mode; Turning On The Control Mode To Make An External Controller Connection - Sony STR-ZA810ES Guia De Instalacion

Ocultar thumbs Ver también para STR-ZA810ES:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Settings

Setting up the receiver

Activating the network standby mode

You can keep the network function active even when the
receiver is in standby mode.
1
Select [Setup] - [Network Settings] - [Network
Standby] from the home menu.
2
Select [On].
Turning on the control mode to make an
external controller connection
You can control the receiver from external devices.
1
Select [Setup] - [Network Settings] - [External
Control] from the home menu.
2
Select [On].
Note
• Set [External Control] to [On] to activate the network connection or
to activate control from an external controller connected to the
RS232C port.
Outputting a test tone from each speaker
(Test Tone)
You can output a test tone from each speaker in sequence.
1
Select [Setup] - [Speaker Settings] - [Test Tone]
from the home menu.
2
Select the setting you want.
Off
Auto: The test tone is output from each speaker in
sequence.
Front L, Center, Front R, Surround R, Surround L, Sur
Back R, Sur Back*, Sur Back L, Height L, Height R,
Subwoofer: You can select which speakers will output
the test tone.
* [Sur Back] appears when only one surround back speaker is
connected.
3
Adjust the speaker level.
Tips
• To adjust the level of all speakers at the same time, press  +/–.
You can also use MASTER VOLUME on the receiver.
• The adjusted value is shown on the TV screen while adjusting.
12
US
Adjusting the sound balance automatically
(Auto Calibration)
This receiver is equipped with a D.C.A.C. EX (Digital Cinema
Auto Calibration EX) function, which allows you to perform
automatic calibration.
Auto Calibration allows you to perform automatic calibration
as follows.
– Check the connection between each speaker and the
receiver.
– Adjust the speaker level.
– Measure the distance of each speaker from your seating
position.*1
– Measure the speaker size.*1
– Measure the frequency characteristics (EQ).*1
– Measure the frequency characteristics (Phase).*1 *2
*1 The measurement result is not utilized when [Direct] is selected.
*2 The measurement result may be not utilized, depending on the
audio formats.
Note
• The D.C.A.C. EX function is designed to achieve proper sound
balance for your room. However, you can adjust the speaker levels
manually according to your preference using Test Tone.
1
Set up each speaker correctly, and then connect
the calibration microphone.
2
Select [Setup] - [Speaker Settings] - [Auto
Calibration] from the home menu.
3
When you use height/overhead speakers, select
[Change Surround Back Speaker Assign], and
then select [Height Speakers] on the next screen.
4
Select [Proceed to configure the speaker
pattern], and then set the speaker pattern on
the next screen.
If you have set [Height/Overhead speakers] to a value
other than [FH] (front high speakers) or [--], set
[Ceiling Height] on the next screen.
5
Make sure that the calibration microphone is
connected to the receiver, and then select
[Proceed to the next step].
6
Confirm the instructions on the screen, and then
press
to select [Start].
The measurement starts in 5 seconds.
The measurement process takes approximately 30
seconds. A test tone is output from each speaker in
sequence.
When the measurement ends, a beep sounds and the
screen switches.
7
Select the item you want.
Save: Saves the measurement results and exits the
setting process.
Retry: Performs the Auto Calibration again.
Discard: Exits the setting process without saving the
measurement results.
8
Save the measurement results.
Select [Save] in step 7.

Publicidad

Tabla de contenido
loading

Tabla de contenido