Batteries Disposal; Batteries Charge Level Indicator; Hour Meter; Squeegee Assembly - Tornado 99680T Manual De Instrucciones

NOTE: Never leave batteries completely discharged
even if the machine is not used. In case of traditional
batteries, please check the electrolyte level every 20
recharging cycles and eventually fill them up with
distilled water.
ATTENTION:
For the daily recharge of the batteries it is necessary
to follow strictly all the indications given by the
manufacturer/distributor. All the installation and
maintenance operations must be carried out by
qualified staff. Danger of gas exhalations and
emission of corrosive liquids. Fire danger: do not
approach with free flames.

BATTERIES DISPOSAL

It is compulsory to hand over exhaust batteries, clas-
sified as dangerous waste, to an authorized institu-
tion according to the current laws.

BATTERIES CHARGE LEVEL INDICATOR

WHEN THE MACHINE IS SWITCHED ON, ON THE DIS-
PLAY (1) APPEARS THE SETTING OF THE BATTERY
CHECK CARD:
GE 24: check card set for GEL batteries.
Pb 24: check card set for lead batteries.
On the display (1) the following indication of the
battery charge level is digital and indicates the per-
centage of the battery charge. 90 is the maximum
charge, down to a minimum of 10, indicating every
10% decrease.
When the charge level reaches 10%, the display
starts blinking indicating the end of the battery
charge.
ATTENTION:
After a few seconds from the four blinking ''----''
dashes, the brushes motor stops automatically. With
the remaining charge it is anyhow possible to finish
the drying operation before proceeding to the re-
charge.

HOUR METER

The machine is equipped with an hour meter located
on the same display of the battery charge level indi-
cator (1). Keeping the button (2) pressed for more
than 3 seconds, the first data indicates the working
hours and after a few seconds the working minutes
are shown.

SQUEEGEE ASSEMBLY

With the squeegee support lowered, slide the two
stud bolts (1) placed on the upper part of the squee-
gee inside the slots on the support. Block the squee-
gee by rotating the lever (2) clockwise.
Insert the squeegee hose (3) into its coupling, re-
specting its position as indicated in the figure.

ADJUSTMENT OF THE SQUEEGEE HEIGHT

The squeegee must be adjusted in height depending
on the rubber wear. In order to guarantee a perfect
drying during the operation, the lower blade of the
rear squeegee rubber (4) must work slightly bent
backwards (operator side) in uniformed way in all its
length.
Acting clockwise upon the two registers (5) it is pos-
sible to increase the bending of the rubber. Acting
counterclockwise it is possible to decrease the rubber
bending.
A label placed near the two registers (5) indicates ro-
tation sense to increase or reduce the height.
Note: The wheels of the squeegee support must be
adjusted through the registers (5) at the same height
so that the squeegee works parallel to the floor.
20

ADJUSTMENT OF THE SQUEEGEE INCLINATION

In case of need, to increase the rubber bending in
the central part, it is necessary to tilt the squeegee
rotating counterclockwise the register (6). To in-
crease the rubber bending on the squeegee extremi-
ties, rotate the register clockwise.

SPLASH GUARD ASSEMBLY

The two splash guards have to be assembled onto the
brushes base group. Insert the metal strips inside the
suitable slots present on the rubber. Place the round
hole at the flat extremity of the strip onto the screw
placed in the front part of the brushes base group.
Secure the strips through the nut blocking it.
Hook the spring in the rear part of the brushes base
group to the slot placed at the extremity of the met-
al strip still free. Please act as above for both the
splash guard rubbers, paying attention to reduce to
the minimum the gap between the two rubbers in
the front part of the brushes base group.
With brushes assembled, the splash guard must
slightly touch the floor.

BRUSH/ES ASSEMBLY

1. Switch off the machine acting upon the general
switch (12). For machines equipped with key switch
(see under "OPTIONAL ACCESSORIES"), turn the key
counterclockwise.
2. Acting upon the pedal (10) lift the brushes base
group.