Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
TO REMOVE WHEELS (See Fig. 25)
•
Remove the klik pin and remove wheel from axle.
IMPORTANT: When installing wheel, be sure to use the
axle hole closest to the end of the shaft - do not use the
hole in the wheel hub (if equipped). Inner hole in axle and
hole in wheel hub are not used for your model snow thrower,
KLIK PIN (INSTALL
IN OUTER HOLE
OF AXLE ONLY)
OUTER HOLE
AXLE
WHEEL"
WHEELHUB
NOTE: To seal punctures or prevent flat tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer, Tire sealant also prevents ti re dry rot and corrosion.
ENGINE
CARBURETOR
Your carburetor is not adjustable. Engine performance
should not be affected at altitudes up to 7,000 feet (2,134
meters). If your engine does not operate properly due to
suspected carburetor problems, take your snow thrower
to a Sears service centre/department.
FIG. 25
STORAGE
ENGINE SPEED
Never tamper with the engine governor, which is factory set
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be dangerous and will
void the warranty. If you think the engine-governed
high
speed needs adjusting, contact a Sears Parts & Repair
Center, which has the proper equipment and experience
to make any necessary adjustments,
Immediately prepare your snow thrower for storage at the
end of the season or if the unit will not be used for 30 days
or more,
&
WARNING:
Never
store
the
snow
thrower with gasoline in the tank inside
a building where fumes may reach an
open flame, spark or pilot light as on a
furnace, water heater, clothes dryer or
gas appliance. Allow the engine to cool
before storing in any enclosure.
SNOW THROWER
When snow thrower is to be stored for a period of time,
clean it thoroughly, remove all dirt, grease, leaves, etc,
Store in a clean, dry area,
1,
Clean entire snow thrower (See "CLEANING" in the
Maintenance section of this manual).
2.
Inspect and replace belts, if necessary (See "TO RE-
PLACE BELTS" in the Service and Adjustments section
of this manual),
Lubricate as shown in the Maintenance section of this
manual,
3,
4.
5,
Be sure that all nuts, bolts, screws, and pins are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
ENGINE
FUEL SYSTEM
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
fuel hose, or tank during storage. Alcohol blended fuels
(called gasohol or using ethanol or methanol) can attract
moisture which leads to separation and formation of acids
during storage, Acidic gas can damage the fuel system of
an engine while in storage,
•
Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
•
Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
•
Use fresh fuel next season,
NOTE: Fuel stabilizer is an acceptable alternative in min-
imizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container,
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor, Do not empty
the gas tank and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace with clean en-
gine oil. (See "ENGINE" in the Maintenance section of
this manual),
CYLINDER
1.
Remove spark plug.
2,
Pour approximately one ounce (30 ml) of oil through
spark plug hole into cylinder,
3.
Pull recoil starter handle slowly a few times to distribute
oil.
4,
Replace with new spark plug,
OTHER
•
Do not store gasoline from one season to another.
•
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems,
•
If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.
•
Cover your snow thrower with a suitable protective
cover that does not retain moisture. Do not use plastic.
Plastic cannot breathe, which allows condensation to
form and will cause your snow thrower to rust,
IMPORTANT: Never cover snow thrower while engine/
exhaust area is still warm,
19
Publicidad
Tabla de contenido
