Specifications; Programming The Remote Control; Remote Control Codes - Insignia NS-PDP72 Guia Del Usuario

Problem Solution
Unusual sounds are coming • A change in humidity or
from inside your plasma TV.
In PC mode, the signal is out • Adjust the resolution or
of range.
• Make sure that the PC is
In PC mode, the picture has • Use the auto adjust feature
vertical bars or stripes, there
is horizontal noise, or the
image position is incorrect.
In PC mode, the color is • Make sure that the cables
unstable or there is only one
color.
• Reinstall the PC video card

Specifications

Specifications subject to change without notice.
Power requirement AC100-240 V @ 50/60 Hz
Television system NTSC-M
ATSC
64 and 256 QAM
Channel coverage VHF 2-13
UHF 14-69
CATV 1-135
DTV 2-69
CADTV 1-135
External antenna impedance 75 ohm
Temperature Operating:
32° to 104°F (0° to 40°C)
Storage:
-4° to 104°F (-20° to 60°C)
Humidity Operating: < 80%
Storage: < 85%
Dimensions (W × H × D) Including stand:
44.4 × 29.5 × 15.0 inches
(112.9 × 74.85 × 3181.0 cm)
Excluding stand:
41.3 × 27.4 × 4.1 inches
(112.9 × 69.5 × 10.37 cm)
Weight Including stand:
64.4 lbs. (29.2 kg)
Excluding stand:
55.8 lbs. (25.3 kg)
24
Programming the remote
control
temperature may result in
unusual sounds when you
turn your plasma TV on or
off. This is normal and
does not indicate that your
plasma TV is not working
correctly.
the horizontal or vertical
frequency.
connected correctly and
securely.
to automatically adjust the
image, or adjust the clock,
phase, or vertical or
horizontal position options
in the OSD.
are connected correctly
and securely.
or driver.

Remote control codes

VCRs
AIWA
AKAI
AMPRO
ANAM
AUDIO
DYNAMICS
BROKSONIC
CANON
CAPEHART
CRAIG
CURTIS MATHES 031 033 041
www.insignia-products.com
Insignia NS-PDP42 42" Plasma TV-720P
You can program the provided remote control to
operate most remote controllable devices.
Note
The provided remote control may not work with all
models or brands.
To find out if the remote control can operate
a device without programming:
1 Turn on the device (such as a VCR), then
press the corresponding mode button on the
remote control for the device.
2 Press POWER. If the device turns off, you do
not need to program the remote control. If the
device does not turn off, you need to program
the remote control
To program the remote control:
1 Turn on the device (such as a VCR), then
press the corresponding mode button on the
remote control for the device.
2 Press and hold MENU and MUTE at the
same time for two seconds. The button for
the currently selected device lights.
3 Press the number buttons for the appropriate
code for the device. For a list of codes, see
"Remote control codes" on page 24.
4 Press the mode button for the device. If the
device turns off, you have programmed the
remote control correctly.
Note
If you do not enter a code within 20 seconds of
pressing MENU and MUTE, programming is
cancelled.
5 Press MENU to store the code. The remote
control LED blinks twice, and the code is
stored.
6 Test various remote control buttons with the
device. If some of the buttons do not work
correctly, repeat this task and enter a
different code.
034 OPTONICA
016 043 046 PANASONIC
124 125 146
072 PENTAX
031 033 103 PHILCO
012 023 039 PHILIPS
043
035 037 129 PILOT
028 031 033 PIONEER
108 PORTLAND
003 040 135 PULSAR
QUARTZ
053 054
066 070 074
083 133 140
145
013 020 031
033 063
031 034 067
031 033 034
054 067 071
101
101
013 021 048
108
072
011 014