Important Remarks; Important Safety Instructions - Riello Elettronica CARDIN BLi Serie Manual De Instrucciones

IMPORTANT REMARKS

READ THE FOLLOWING REMARKS CAREFULLY BEFORE PROCEEDING WITH THE INSTALLATION.
PAY PARTICULAR ATTENTION TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
IMPORTANT INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING ORDER OF THE SYSTEM AND CREATE
DANGER SITUATIONS FOR THE USERS OF THE SYSTEM. SAVE THESE INSTRUCTIONS FOR FUTURE USE.
THE INTEGRATED CARDIN SYSTEMS ARE DESIGNED AND BUILT ONLY
TO BE USED IN MADE TO MEASURE METALLIC STRUCTURES. CARDIN
ELETTRONICA DO NOT GUARANTEE PRODUCTS THAT HAVE BEEN
INSTALLED IN A WAY THAT DOES NOT CONFORM TO THE SUPPLIED
INDICATIONS.
It therefore follows that the structure should be constructed in such a way
as to guarantee the following characteristics:
A
B
• Suitable for housing electronic appliances:
- the upper part must be completely sealed, so as not to allow water infiltra-
tion (IP55) (det. A);
- Air vents should be fitted in both the upper and lower parts of the columns
in order to avoid condensate build up (det. B);
• Conformity with the dimensional and structural characteristics as stipulated
by good building practice
• The end structure should respect the parameters as laid down by the stand-
ards and regulations in force UNI EN 12453 with regard to maintaining safety
conditions during the use of motorized gates and doors.
The geared motor is normally installed with the drive shaft pointing up-
wards (det. A). To position the motor with the driveshaft pointing downwards
(det. C) create a supplementary cover within the column where necessary.
• These instructions are aimed at professionally qualified "installers of electrical
equipment" and must respect the local standards and regulations in force.
All materials used must be approved and must suit the environment in which the
installation is situated.
• All maintenance operations must be carried out by professionally qualified techni-
cians. Before carrying out any cleaning or maintenance operations make sure the
power is disconnected at the mains.
• This appliance must be used exclusively for the purpose for which it has been made.
"i.e. for the automation of hinged gates" with one or two gate leaves, max. length
1,8 m max. weight 150 kg.
The unit may be fitted both to the right and to the left of the passageway and has
a maximum opening angle of 180°.
Caution! a mechanical stop buffer must be installed.

IMPORTANT SAFETY INSTRUCTIONS

• This appliance must never be used by people (including children) with physical,
sensory or mental disabilities or by people without specific knowledge and experi-
ence in its operation unless they are able to benefit from the experience or are
being taught to use the appliance whilst being safeguarded by the presence of
somebody responsible for their safety.
• Before installing make sure that the guided parts are in good condition, correctly
balanced and that they open and close correctly.
• Avoid becoming trapped between the hinged parts and the fixed parts during the
opening and closing movements.
• The motor's power cable must be made of polychloroprene in conformity with the
international standard 60245 IEC 57.
It is the responsibility of the installer to make sure that the following public safety
conditions are satisfied:
1) Ensure that the gate operating installation is far enough away from the main road
to eliminate possible traffic disruptions.
2) The motor must be installed on the inside of the property and not on the public side
of the gate. The gates must not open onto a public area.
3) The gate operator is designed for use on gates through which vehicles are passing.
Pedestrians should use a separate entrance. The unit cannot be used together with
a pedestrian door unless it is fitted with a separate device with which to control the
pedestrian door.
4) The controls (including safety controls ) must be installed at a height between
1,5 and 1,8 m and in a location not accessible to children. Controls installed
externally must be protected by a safety device inhibiting unauthorised use.
IMPORTANT REMARKS
5) At least two warning signs (similar to the example on the right)
should be placed, where they can be easily seen by the public,
in the area of the system of automatic operation. One inside the
property and one on the public side of the installation. These
signs must be indelible and not hidden by any objects (such as
tree branches, decorative fencing etc.).
6) Make sure that the end-user is aware that children and/or pets must not be
allowed to play within the area of a gate installation. If possible include this
in the warning signs.
C
7) Whenever a fully open gate leaf comes within ≤ 500 mm of a fixed structure
the space must be protected by an anticrush buffer.
8) If you have any questions about the safety of the gate operating system, do
not install the operator. Contact your dealer for assistance.
TECHNICAL DESCRIPTION
• The set consists of:
2 geared motors 200/BLi824 with an incorporated encoder without onboard
electronics;
1 electronic programmer CC242EINT with NiMH batteries, a battery charger
and an integrated S449 radio frequency module.
• The geared motor is powered by 24 Vdc and is fitted with a permanently
lubricated four-stage epicycloid reduction unit.
• The geared motor is fitted with an Allen key operated manual release system.
• The geared motor is connected to the electronic programmer by means of a
6 wire cable.
• Electronic programmer for two encoder-controlled 24 Vdc motors that allow the
precise position control of hinged gates. Monitoring the current consumption
allows the control of a sophisticated anticrush safety system, and the "soft
start" and "soft stop" functions reduce the stress on the mechanical compo-
nents. The electronic components , housed in a shock-proof plastic container
IP55, come complete with a battery charger and buffer batteries allowing
emergency manoeuvring and a radio frequency module for remote control.
Gate travel time programming is fully automatic and guided by a display.
Dip-switches allow you to set the system parameters including: the sequential
button mode, automatic reclosing, warning lamp pre-flashing, intermittent warn-
ing lamp activation, indicator light and photoelectric cell function setting and
electric lock enable. The six figure display allows you to visualise the number
of manoeuvres carried out and to set several parameters such as the type of
motor, the torque setting and the limited opening distance.
USER INSTRUCTIONS
differential collection, environmental friendly treatment and disposal contributes
to avoiding negative effects on the ambient and consequently health as well as
favouring the recycling of materials. Illicitly disposing of this product by the owner
is punishable by law and will be dealt with according to the laws and standards
of the individual member nation.
During the opening/closing manoeuvre check for correct operation and activate the
emergency stop button in case of danger.
During blackouts the gate can be released and manually manoeuvred using the sup-
plied release key (see manual release pag. 13).
Periodically check the moving parts for wear and tear and grease if required using
lubricants which maintain their friction levels unaltered throughout time and are suitable
for temperatures of -20 to +70°C.
In case of failure or operational anomalies switch off the power at the mains do not
attempt to repair the appliance yourself.
Periodically check the correct operation of all safety devices (photoelectric cells etc.).
Eventual repair work must be carried out by specialised personnel using original
spare parts.
The appliance is not suitable for continuous operation and must be adjusted according
to the model (see technical data on page 48).
12
IMPORTANT REMARKS
. NOT READING THESE
Attention! WEEE marking. This symbol indicates that once the
products life-span has expired it must be disposed of separately from
other rubbish. The user is therefore obliged to either take the product
to a suitable differential collection site for electronic and electrical
goods or to send it back to the manufacturer if the intention is to
replace it with a new equivalent version of the same product. Suitable
WARNING
AUTOMATIC OPENING
KEEP CLEAR
CHILDREN OR PETS MUST NOT
BE ALLOWED TO PLAY ON OR
NEAR THE INSTALLATION