External Cleaning - Tecfrigo SNELLE 400 GBT Instalación Y Uso

Operator's guide:
1)Unpacking instructions
2)The handles
3)Cleaning of the internal
I

4)External cleaning

5)Connections to mains
UK
6)Controls
7)Checking the correct functioning
D
8)Internal cleaning
9)Replacement of the interna light
E
10)Replacement of the door's magnetic gasket
F
!
WARNINGS
It is most important that this instruction booklet is kept together with the appliance both for future
NL
reference and for reasons of safety.
1
. Adults should operate this appliance only. Do not allow children to use the controls or play with it.
P
is forbidden to modify in any way the main functions and characteristics of this appliance. . The electrical
installation of the appliance should be carried out by a qualified electrician or other competent person.
S
4
. Never attempt to carry out repairs unassisted. Inexpert repairs can cause serious damage and
5
malfunction. . This appliance is not suitable for the storage of basic commodities not including food-
DK
6
stuffs. . The manufacturers of this appliance accept no responsibility for the consequences of misuse in
contravention of these safety instructions. It further reserves the right to carry out improvements without
FIN 7
prior notice.
near sources of heat, such as radiators, stoves, etc. . Keep the ventilation grills free from obstruction for
B at least 30 cm.
11
edges. . If damp air or products to be refrigerated should cause ice to form on the evaporator, we
recommend stopping the compressor and placing the goods in special refrigerated containers, kept at the
GR
same temperature, until defrosting is completed;if this is not carried out the compressor will continue to
operate leading to a wasteful consumption of electricity and poor performance.
CZ
working and unused, it is indispensable to keep the door open at least 10 cm. Avoiding this, you will avoid
also the consequent mildew formation and unpleasant smells.
EE
refrigeration is off.
LV
!
Our products are for internal use only do not install outside restaurants, shops.
LT
!
Assistance has to be provided by an authorized engineer only. Always use original spare parts.
H
1. UNPACKING INSTRUCTIONS
M
CARDBOARD PACKAGING 1a
WOODEN CRATE
upwards.
PL
fork-lift truck between appliance and pallet or crate. . Lift the appliance. . Remove the pallet or crate.
5
. Place the appliance on a horizontal level surface. . Pay attention anything is left inside the packing.
SK
7
. Separate the packing materials according to their type, for easier disposal (See picture 1).
2. THE HANDLES
1.
SLO
The handles will be found into a package inside the appliance. . Fix the base part of the handle using
the two screw inserted on the holes already. Tighten with care.
until it clicks into place
3. CLEANING OF THE INTERNAL
1
. Only clean the internal components and glass panels with a soft, wet sponge and a neutral detergent.
2
. Dry with care using a soft cloth.
4. EXTERNAL CLEANING
1
. For the glass panels use the same products as used for the internal cleaning.
tape from the steel panel and from the grids (See picture 3).
5. CONNECTIONS TO MAINS
1.
Ensure that mains voltage and frequency are the same as those stated on the rating plate
to the appliance.
earthed. b) It is appropriate for the nominal current as set out on the rating plate.
IEC regulations: -Magneto-thermic differential switch with in=nominal value as stated on the rating plate;
-Differential with ID sensitivity = 30 mA.
4.
The connecting cable to the appliance is H05 VVF, designed for internal use only.
appliance, during the transport or storage, has been erroneously placed in horizontal position or upside-
down, it must be left in the correct vertical position for at least 3 hours before connecting it to the electrical
5.
supply. Insert the plug (do not use triple and reductions outlets) ( see picture 4).
. Avoid installing the cabinet directly in line with sunlight. . Nevere install the appliance
10
. Ensure that the products displayed on the shelves and grills do not hang over the
. Cut surrounding tape. Remove the cardboard packaging by sliding
1b
. Remove the nails from the wooden crate with care. . Insert forks of
(See picture 2).
2.
Ensure that the supply socket has the following characteristics:
Operator's guide
Maintenance manual (Page 48):
1)Cleaning the condenser
2)Replacement of a glass panel
3)Wiring diagram diagram of refrigeration unit
9
13.
3
6
2
3.
Place the plastic part and press down
3.
Ensure that there is no danger of explosion (AD) in the room.
6
3
8
12
. If the appliance is not
Do not keep the neon light up if the
2
4
2
. Remove the protection
It is properly
a)
c) It complies with the
Notice:
2
. It
(A)
attached
in case of