Elko EP AirWD-100 Serie Manual Del Usuario página 3

ELKO EP, s.r.o.
Palackého 493
769 01 Holešov, Všetuly
Czech Republic
Tel.: +420 573 514 211
e-mail: elko@elkoep.com
www.elkoep.com
Made in Czech Republic
02-103/2017 Rev.: 0
Characteristics
• The magnetic detector is used to detect motion – it is activated by attaching /
removing the magnet from the sensor.
• The Sigfox, LoRa or NB-IoT network can be used for message transmission.
• Anti-sabotage function (tamper): When unauthorized interference with the detec-
tor occurs (disassembly) it sends an information message to the server.
• Data is sent to the server from which it can be subsequently displayed as a smart-
phone, application, or Cloud notifi cation.
• Battery status information is sent as a message to the server.
• Power supply: 1x CR123A battery life approx. 2 years (depending on frequency
of use).
General instrucions
Internet of Things (IoT)
• The IOT wireless communications category describes the Low Power Wide Area
(LPWA). This technology is designed to provide full-range coverage both inside and
outside buildings, energy-saving and low-cost operation of individual devices. Indi-
vidual networks - Sigfox, LoRa, NarrowBand - are available to use this standard.
Sigfox network information
• The network supports bidirectional communication but with a limited number of feed-
backs. It uses the free frequency band divided by Radio Frequency Zones (RCZ).
• RCZ1 (868 MHz) Europe, Oman, South Africa
• RCZ2 (902 MHz) North America
• RCZ3 (923 MHz) Japan
• RCZ4 (920 MHz) South America, Australia, New Zealand, Singapore, Taiwan
• Sigfox has more coverage across countries, so it is better suited for long distance moni-
toring.
• For more information on this technology, please visit www.sigfox.com.
LoRa network information
• The network is bidirectional and its communication uses free frequency band.
• 865 - 867 MHz India
• 867 - 869 MHz Europe
• 902 - 928 MHz North America, Japan, Korea
• The advantage of this network is the possibility of freely deploying individual stations
in local locations, thus strengthening their signal. It can therefore be used effi ciently in
company premises or, for example, in local parts of cities.
• For more information on this technology, please visit www.lora-alliance.org.
Information about the NarrowBand network
• The network provides two-way communication and the only one to use the licensed
LTE band. Our devices allow band 1 (2100MHz), Band 3 (1800MHz), Band 8 (900MHz),
Band 5 (850MHz), Band 20 (800MHz) and Band 28 (700MHz).
• It uses this SIM card technology for each device.
• The advantage of NarrowBand is the use of already built-up grids, which ensures suf-
fi cient reception outside and inside buildings.
• For more information on this technology, please visit www.vodafone.cz
Caution for proper operation:
• Products are installed according to the wiring diagram given for each product.
• For proper device functionality, it is necessary to have suffi cient coverage of the se-
lected network at the installation site.
• At the same time, the device must be registered in the network. Successful device reg-
istration on a given network requires a charge for traffi c.
• Each network off ers diff erent tariff options - it always depends on the number of mes-
sages you want to send from your device. Information on these tariff s can be found in
the current version of the ELKO EP pricelist.
AirWD-100
Magnetic detector (indoor)
Description
Detector D/WD
1
2
-
3 3
6
4
+
5
Cloud app assignment
It is done in your Smartphone application. Enter the relevant information on the product
cover into the application.
Function
• When the battery is inserted, the detector sends an initial message, the red LED blinks.
• Activation occurs when the magnet is attaching / removed from the sensor.
• The detector sends a data message every 12 hours. In case of a state change, it
sends the data message immediately.
• In case of an open box, every movement of the magnet in/out is indicated by the blink-
ing of the red LED. In the case of a weak battery when moving in / out of the magnet is
indicated by the LED flash twice.
Assembly
Detector
2b
1
5
AirWD-100NB
6
1. Push the screwdriver into the hole at the bottom of the detector, slide the upper cover
by pulling it up and open the detector.
2. The product can be attached in two ways:
a) Directly on a fl at surface by gluing * - Apply a suitable adhesive to the outside of the
base. Place the base at the desired location (moving window or door leaf ) and allow
to dry.
b) Using a suitable fastener ** by screwing - lower the molding at the bottom of the
machine and pull it out of the base.
3. b) Break and remove the screw plugs (e.g. with a Screwdriver).
4. b) Drill the two holes of the appropriate diameter corresponding to the position of the
holes in the bottom of the box in the required position (moving wing of the window or
door). Place the base at the desired location and attach it with suitable bonding material
according to the substrate.
1 / 2
1. Antenna
2. NanoSIM slot (AirWD-100NB only)
3. Magnetic contact
4. Battery
5. Tamper
6. Magnet
3b 4b
7
-
+
EN
-
+
Click!