Publicidad
3. PRUEBA DE DIAGNOSTICO LOCAL
Antes de probar, separe la base de la cubierta (vea Fig. 3a).
A. Presione el interruptor de sabotaje una vez y libérelo.
B. Vuelva a poner la cubierta para devolver el interruptor de sabotaje a su posición normal (no perturbada), y luego asegure la cubierta
frontal a la base con el tornillo de cierre de caja.
C. Abrir un momento la puerta o ventana y verificar que el LED rojo parpadea, indicando detección.
D. Después de 2 segundos el LED parpadea 3 veces.
La siguiente tabla muestra la indicación de fuerza de señal recibida.
Respuesta LED
LED verde parpadea
LED naranja parpadea
LED rojo parpadea
Sin parpadeo
IMPORTANTE! Debe de asegurarse una recepción confiable. Por lo tanto, no es aceptable una fuerza de señal "pobre". Si recibe una
señal "pobre" desde el dispositivo, cambie de ubicación y vuelva a probar hasta recibir una fuerza de señal "buena" o "fuerte".
Nota: Para instrucciones de Prueba de Diagnóstico detalladas consulte la Guía del Instalador del panel de control.
4. COMENTARIOS MISCELÁNEOS
Los sistemas inalámbricos de Visonic Ltd. son muy confiables y comprobados con altos estándares. Sin embargo, debido a baja
potencia de transmisión y rango limitado (requeridos por la FCC y otras autoridades regulatorias), hay que considerar algunas
limitaciones:
A. Los receptores pueden ser bloqueados por señales de radio que aparecen sobre o cerca de sus frecuencias de operación, sin
importar el código digital utilizado.
B. Un receptor responde solamente a una señal transmitida a la vez.
C. Dispositivos inalámbricos deben ser probados en forma regular para determinar si hay fuentes de interferencia y para protegerlos
contra fallas.
5. CUMPLIMIENTO CON ESTÁNDARES
Cumplimiento con
Estándares
FCC Compliance Statement
The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio and television reception. However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause such interference, which can be verified by turning the device off and on, the user is
encouraged to eliminate the interference by one or more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one which supplies power to the receiver.
–
Consult the dealer or an experienced radio/TV technician
IC statement:
This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisee aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.
WARNING!
To comply with FCC and IC RF exposure compliance requirements, the device should be located at a distance of at least 20 cm from all
persons during normal operation. The antennas used for this product must not be co-located or operated in conjunction with any other
antenna or transmitter.
WARNING!
The user is cautioned that changes or modifications to the unit, not expressly approved by Visonic Ltd., could void the user's FCC or
other authority to operate the equipment.
D-303556 MC-302E PG2 Instrucciones de Instalación
Recepción
Fuerte
Bien
Débil
No hay comunicación
USA: CFR 47 part 15 (FCC)
Canada: RSS 210
This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
The Power G peripheral devices have two- way communication functionality, providing additional benefits as described in
the technical brochure. This functionality has not been tested to comply with the respective technical requirements and
should therefore be considered outside the scope of the product's certification.
3
Publicidad
