Install The Door Control - Craftsman 139.54930 Manual Del Propietário

INSTALLATION STEP 11

Install the Door Control

Locate door control within sight of door, at a minimum height of 5
feet (1.5 m) where small children cannot reach, away from moving
parts of door and door hardware. If installing into drywall, drill
5/32" holes and use the anchors provided. For pre-wired
installations (as in new home construction), it may be mounted to
a single gang box (Figure 1). NOTE: Install door control on a flat
surface.
1. Strip 7/16" (11 mm) of insulation from one end of bell wire and
connect to the two screw terminals on back of door control by
color: white wire to 2 and white/red wire to the 1 (Figure 2).
2. Remove white cover by gently prying at slot in top of the cover
with a small flat head screwdriver (Figure 3). Fasten with
6ABx1" self-tapping screws (drywall installation) or 6-32x1"
machine screws (into gang box) as follows:
Install bottom screw, allowing 1/8" (3 mm) to protrude
l
above wall surface.
Position bottom of door control on screw head and slide
l
down to secure. Adjust screw for snug fit.
Drill and install top screw with care to avoid cracking
l
plastic housing. Do not overtighten.
Insert top tabs and snap on cover.
l
3. (For standard installation only) Run bell wire up wall and
across ceiling to motor unit. Use insulated staples to secure
wire in several places. DO NOT pierce wire with a staple,
creating a short or open circuit.
4. Strip 7/16" (11 mm) of insulation from end of bell wire.
Connect bell wire to the quick-connect terminals as follows:
white to white and white/red to red (Figure 4).
NOTE: When connecting multiple door controls to the opener,
twist same color wires together. Insert wires into quick-
connect holes: white to white and red/white to red.
5. Position the antenna wire as shown.
6. Use tacks or staples to permanently attach entrapment
warning label to wall near door control, and manual
release/safety reverse test label in a prominent location on
inside of garage door.
NOTE: DO NOT connect power and operate opener at this time.
The trolley will travel to the full open position but will not return to
the close position until the sensor beam is connected and
properly aligned.
Figure 4 Door Control
To release or insert wire,
Connections
push in tab with screwdriver tip
Strip wire 7/16" (11 mm)
Red White Grey
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
Be sure power is NOT connected BEFORE installing door
l
control.
Connect door control ONLY to 24 VOLT low voltage wires.
l
To prevent possible SERIOUS INJURY or DEATH from a closing
garage door:
Install door control within sight of garage door, out of reach
l
of children at a minimum height of 5 feet (1.5 m), and away
from ALL moving parts of door.
NEVER permit children to operate or play with door control
l
push buttons or remote control transmitters.
Activate door ONLY when it can be seen clearly, is properly
l
adjusted, and there are no obstructions to door travel.
ALWAYS keep garage door in sight until completely closed.
l
NEVER permit anyone to cross path of closing garage door.
HARDWARE SHOWN ACTUAL SIZE
Screw 6ABx1"
(std installation)
Screw 6-32x1"
(Gang box installation)
Figure 1
PRE-WIRED
INSTALLATION
Figure 3
REMOVE &
REPLACE COVER
7/16" (11 mm)
2-Conductor
Bell Wire
Lighted
Push Button
STANDARD
CONTROL CONSOLE
22
Insulated Staples
(Not shown)
Drywall Anchors
Figure 2
(BACK VIEW)
24 Volt
Bell
2-Conductor
Wire
Bell Wire
To Replace,
Insert Top Tabs
First
Top
Mounting
Hole
Terminal
Screws
Bottom
Mounting
Hole
To Remove,
Twist Here