Preface; Introduction; Product Description - PLYMOVENT T-FLEX/CW Manual Del Usuario

ENGLISH

PREFACE

Using this manual
This manual is intended to be used as a work of reference for
professional, well trained and authorised users to be able to
safely install, use, maintain and repair the product mentioned
on the cover of this document.
Pictograms and symbols
The following pictograms and symbols are used in this manual:
TIP
Suggestions and recommendations to simplify
carrying out tasks and actions.
CAUTION!
Procedures, if not carried out with the necessary
caution, could damage the product, the workshop or
the environment.
WARNING!
Procedures which, if not carried out with the necessary
caution, may damage the product or cause serious
personal injury.
WARNING!
Fire hazard! Important warning to prevent fire.
Text indicators
Listings indicated by "-" (hyphen) concern enumerations.
Listings indicated by "•" (bullet point) describe steps to perform.
Service and technical support
For information about specific adjustments, maintenance or
repair jobs which are not dealt with in this manual, please
contact the supplier of the product. He will always be willing to
help you. Make sure you have the following specifications at
hand:
- product name
- serial number
These data can be found on the identification plate.
1

INTRODUCTION

1.1 Identification of the product
The identification plate contains, among other things, the
following data:
- product name
- serial number
1.2 General description
The T-Flex/CW is a wall-mounted telescopic extraction arm with
a rotatable hood. Incorporated into the hood is a throttle valve
that can be fully opened, partially opened or completely closed
to control airflow at hood opening. The arm features a focus
extraction spoiler, which directs the air into the hood.
The extraction arm is based on a telescopic tube, allowing it to
be extended to give a 2,5 m (8.2 ft) working radius and
compressed to 1,5 m (5 ft). The arm is fitted with a spring-
balance which enables it to be moved from a vertical to a
horizontal position in one easy movement.
If mounted on a column, the arm can be turned through 300°
due to the rotating hinge. The T-Flex/CW is often used in
welding cabins.
0507291010/260411/A T-Flex/CW
1.3 Product combinations
In order to operate the extraction arm, selection of one of the
following products is required:
- single fan type FAN-14; or
- single fan type FAN-28; or
- single fan type FAN-42; or
- central fan +NCF (flange)
1.4 Options and accessories
The following products can be obtained as an option and/or
accessory:
- WCS (welding cable sensor) + AD-200 or AD-8 (automatic
damper)
- FlowGuard (airflow sensor)
- NCF (flange in case of duct connection)
1.5 Technical specifications
Counterweight
Diameter
Weight (net)
Airflow
1.6 Pressure drop
Refer to Fig. I on page 38.
A Static pressure (Pa)
3
B Airflow (m /h)
C Static pressure (in. WG)
D Airflow (CFM)
1.7 Reach
Refer to Fig. II on page 38.
1 Top view
2 Front view
3 Side view
Refer to the available product data sheet for detailed
product specifications.
1.8 Ambient conditions
Min. operating temperature
Nom. operating temperature
Max. operating temperature
Max. relative humidity
2

PRODUCT DESCRIPTION

2.1 Components
The product consists of the following main components and
elements:
Fig. 2.1
A wall mounting bracket
B counterweight casing
C rotatable hood RotaHood
D hose 1650 mm (65 in.)
E tube
F hose 500 mm (20 in.)
G rotating hinge
H rope
I counterweight
6,5 kg (14.3 lbs)
Ø 203 mm (8 in.)
27 kg (59.5 lbs)
3
max. 1600 m /h (942 CFM)
5°C (41°F)
20°C (68°F)
45°C (113°F)
80%
EN - 8