Alarm Management - Royal IDRO Manual De Instalación, Uso Y Mantenimiento

Estufas de pellets idro
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

11 ALARM MANAGEMENT

If a malfunction occurs, the following procedure is activated:
1) audible alarm (beep);
2) one of the following system LEDs come on:
3) if the problem concerns an error, the stove will switch off.
Pressing and holding the "cancel" button
ERROR/
WARNING CODE
E001
E002
E004
E101
E105
E106
E108*
E108**
E109*
E109**
E110
E111
A001
A002
A007
----
----
2QO\ LQ WKH VWRYHV HTXLSSHG ZLWK PLFUR VDIHW\VZLWFKHV RQ WKH ¿UHER[ GRRU DQG RQ WKH SHOOHW KRSSHU OLG
2QO\ LQ WKH VWRYHV ZLWKRXW PLFUR VDIHW\VZLWFKHV RQ WKH ¿UHER[ GRRU DQG RQ WKH SHOOHW KRSSHU OLG
After having checked the type of message, the alarm can be reset by pressing
the on/off button
,I WKH HUURU FRGH LV ³( RU (´ EHIRUH UHVHWWLQJ WKH DODUP PDQXDOO\ UHVHW
WKH WKHUPRVWDW ORFDWHG RQ WKH UHDU RI WKH VWRYH )LJ  
Then the stove can be started again.
52/136
USE AND & MAINTENANCE
DESCRIPTION
Faulty control panel
Remote control signal communication error Control panel fault
Communication error
Failed ignition error
Outlet water temperature too high
Temperature probe malfunction
Temperature probe malfunction
Safety error
Thermal safety
Pressure error or thermal safety
Pressure error
Temperature probe malfunction
Flue gas temperature probe malfunction
Low pellet level LFRQ ÀDVKLQJ
Scheduled maintenance warning LFRQV
ÀDVKLQJ
Pressure sensor malfunction LFRQ
ÀDVKLQJ
Clean stove
Failed ignition error
for a few moments.
;
shows the error code on the display:
POSSIBLE CAUSES
Control panel fault
Connection cable between board and control panel
interrupted or detached.
,I WKLV DSSHDUV ZKHQ FKDQJLQJ FRQ¿JXUDWLRQ LJQRUH WKH
error
No pellets
Pellet quality
Faulty ignition system
Burn pot dirty
Problems with the heating system
Problems with the pump
Faulty return water temperature probe
Faulty buffer tank temperature probe
Door or hopper lid open
Problems with the heating system
Problems with the pump
Problems with overheating in the pellet hopper
Flue gas exhaust system dirty
Seal gaskets worn
,QVXI¿FLHQW FRPEXVWLRQ DLU
Problems with the heating system
Problems with the pump
Problems with overheating in the pellet hopper
Flue gas exhaust system dirty
Seal gaskets worn
,QVXI¿FLHQW FRPEXVWLRQ DLU
Faulty outlet water temperature probe
Faulty air temperature probe
)DXOW\ ÀXH JDV WHPSHUDWXUH SUREH
Pellets running out
The stove periodically requires maintenance to be
SHUIRUPHG E\ D TXDOL¿HG WHFKQLFLDQ
Pressure sensor or board fault.
&RPEXVWLRQ FKDPEHU EXUQ SRW RU ÀXH JDV H[KDXVW V\VWHP
dirty.
Pressure measuring tubes detached or blocked.
Combustion air intake blocked.
No pellets; Faulty ignition heater; Worn gaskets; Incorrect
burn pot position
cod. 004772131 - 07/2013 - Royal
LED
Fig.11.1

Publicidad

Tabla de contenido
loading

Tabla de contenido