Care And Maintenance - TAKATA MAXI Manual De Instrucciones

CAUTION!
Ensure that the shoulder belt remains in the shoulder
belt guide.
Step 2 – Place the child in the seat
Seat your child in the TAKATA MAXI.
Step 3 – Put the seatbelt on and fasten it
[MAXI_036] Thread the lap belt beneath the red lap
belt guides on the base of the seat. [MAXI_037 +
MAXI_038] The bottom end of the shoulder belt
should also be fed beneath the lap belt guide on the
side of the buckle. Fasten the seatbelt, by pressing the
tongue into the buckle of the seat where the TAKATA
MAXI is positioned.
Step 4 – Check everything
Ensure that your child is seated and secured correctly
in the TAKATA MAXI. Use the following checklist to
do this.
Checklist – using the TAKATA MAXI in a vehicle:
Please check that
‡ WKH 7$.$7$ 0$;, LV XVHG ZLWK D YHKLFOH VHDW WKDW
the manufacturer has labeled as suitable for this class
of child seat;
‡ WKH 7$.$7$ 0$;, LV IDFLQJ IRUZDUGV
‡ WKH 7$.$7$ 0$;, LV VHFXUHG ZLWK DQ DSSURYHG
three-point seatbelt;
‡ ERWK FRQQHFWLRQ DUPV DUH ¿UPO\ DWWDFKHG WR WKH
ISOFIX points (if available);
‡ WKH WRS RI \RXU FKLOG¶V KHDG LV EHORZ WKH WRS HGJH RI
the headrest;
‡ WKH VKRXOGHU EHOW JXLGH LV DURXQG WZR ¿QJHU ZLGWKV
above the child's shoulder;
‡ WKH VKRXOGHU EHOW UXQV WKURXJK WKH VHDWEHOW JXLGH
with the clasp closed;
‡ WKH VKRXOGHU EHOW UXQV RYHU WKH PLGGOH RI WKH
shoulder, and does not touch the neck;
‡ WKH ODS EHOW UXQV EHQHDWK WKH WZR UHG ODS EHOW JXLGHV
‡ WKH ERWWRP HQG RI WKH VKRXOGHU EHOW UXQV EHQHDWK WKH
lap belt guide on the side of the buckle;
‡ WKH WRQJXH RI WKH EHOW LV ORFNHG VHFXUHO\ LQWR WKH
buckle;
‡ WKH YHKLFOH VHDWEHOW UXQV VQXJO\ RYHU WKH FKLOG DQG LV
not twisted.
14

6. CARE AND MAINTENANCE

Removing the covers
Step 1 – Remove the seat back
Remove the back of the TAKATA MAXI as described
in Section 3 – Basic instructions (Removing the seat
back).
Step 2 – Remove the seat back cover
[MAXI_039] Unfasten the two straps at the top and
bottom of the seat back cover, and loosen the cover
around the size indicator.
Step 3 – Remove the side wing covers
[MAXI_040] To remove the covers on the wings,
unfasten the two buttons (one on each wing) on the
inside and the four buttons (two on each wing) on the
outside. The two wing covers can then be pulled off at
the front.
Step 4 – Remove the crash pads from the side wing
covers
WARNING!
[MAXI_041] Each wing cover contains crash pads
that are not washable. To do this, simply pull them out
of the inside pockets of the covers.
Step 5 – Remove the headrest cover
[MAXI_042] Unfasten the two buttons on the back of
the headrest, and the two hooks in the upper area of
the inner side. Loosen the cover by twisting it towards
you and lifting it up from the bottom. Then unfasten
the last two hooks on the edge of the headrest's bottom
and pull the cover down and off.
Step 6 – Remove the crash pad (AIRPADS) from the
headrest cover
WARNING!
[MAXI_043] The headrest cover contains crash pads
(AIRPADS) that are not washable. To do this, simply
pull the crash pads (AIRPADS) out of the two inside
pockets.
Step 7 – Remove the seat base cover
[MAXI_044] Unfasten the two straps on the seat base
cover (one strap on each side), positioned on the outer
sides of the armrests (if this has not already been
done), and pull the cover towards you, off both
armrests. [MAXI_045] Then unfasten the four straps
on the underside of the base, and the two in the