Use In The Vehicle - TAKATA MIDI I-SIZE PLUS Manual De Instrucciones

of the connectors match up (or that both are blank).
Failure to observe this notice may seriously risk your
child's safety, and the safety of other passengers, in
the event of an accident.
Step 4 – Unlock the ISOFIX connectors
[MIDI_I-SIZE_PLUS_030] Unlock the left and
right-hand ISOFIX connectors, by taking hold of the
release sliders on each, moving the locking sliders of
the release sliders down and, at the same time, pulling
the release sliders towards the support leg. The connec-
tors have been correctly unlocked if you can see a red
marking on the top of each slider. If green markings are
shown, the connectors are still locked in place.
Releasing the rear connection hooks
[MIDI_I-SIZE_PLUS_031] The TAKATA MIDI
I-SIZE (PLUS) is attached to the TAKATA I-SIZE
BASE (PLUS) via connection hooks at the front and
rear. To free the TAKATA MIDI I-SIZE (PLUS) from
the TAKATA I-SIZE BASE (PLUS), you need only to
release the rear hooks.
The rear hooks unlock together, so you only need to
push down one of the release elements on the exterior
of the connection arms. The connection hooks have
been correctly unlocked if you can see a red marking
on the top of each release element.
If green markings are shown, both, or in case of
partially green markings possibly only one of the
hooks are still locked in place. Please also see the
warnings in Section 4 – Use in the vehicle (Securing
the TAKATA MIDI I-SIZE (PLUS) in a backward-
facing or forward-facing position).

4. USE IN THE VEHICLE

WARNING!
[MIDI_I-SIZE_PLUS_009] Never use the TAKATA
I-SIZE BASE (PLUS) on its own, or without properly
securing the TAKATA MIDI I-SIZE (PLUS). Failure
to observe this notice may seriously risk your child's
safety, and the safety of other passengers.
NOTE!
Long-term use of the TAKATA I-SIZE BASE (PLUS)
and TAKATA MIDI I-SIZE (PLUS) may result in wear
and tear of the vehicle seat.
Securing the TAKATA I-SIZE BASE (PLUS)
Step 1 – Fold out the support leg
Fold out the support leg as explained in Section 3 –
Basic instructions (Adjusting the support leg), and
ensure that it is properly locked in place.
NOTE!
Check the support leg is locked in place by lightly
shaking it with your hand.
Step 2 – Place on the vehicle seat
[MIDI_I-SIZE_PLUS_032] Place the TAKATA
I-SIZE BASE (PLUS) on the seat of the vehicle.
Ensure that:
• the ISOFIX connectors are pointing to the back of
the car seat
• the support leg is pointing to the vehicle fl oor.
Step 3 – Pull out the ISOFIX connectors
[MIDI_I-SIZE_PLUS_028] Press in the button on the
inner side of each rear connection arm as far as
possible, and fully extend the connectors. Follow the
instruction in Section 3 – Basic instructions (Adjusting
the ISOFIX connectors).
NOTE!
The connectors have been fully extended when no
fi gure is displayed on the top of the ISOFIX connectors.
Step 4 – Connect the ISOFIX system
[MIDI_I-SIZE_PLUS_033] Point the open ISOFIX
connectors on the TAKATA I-SIZE BASE (PLUS)
towards the ISOFIX points of the vehicle. Slide the
connectors into the vehicle's ISOFIX points, until
each one clicks into place, and the green markings are
visible on the release sliders.
NOTE!
[MIDI_I-SIZE_PLUS_034] If the vehicle's ISOFIX
points are diffi cult to reach, use the feeder supplied to
guide them out. This makes connecting the system
much easier, and protects the seat cover.
WARNING!
Ensure that both ISOFIX connectors are fully secured
to the vehicle's ISOFIX points. Failure to observe this
notice may seriously risk your child's safety, and the
safety of other passengers. You can check the connectors
are properly secured to the ISOFIX points, by lightly
shaking the TAKATA I-SIZE BASE (PLUS).
de
en en
fr
it
es
pt
nl
23