Before Switching Off The Power; Preset Functions And Operations - Denon DN-C635 Instrucciones De Operación

ENGLISH
External synchronized recording
The synchronized recording can be use when the DN-C635 is used in combination with DENON other product
(DN-780R etc.).
When the CD player's play button is pressed, a synchronized signal for starting is output from the EXT. SYNC.
jack. When the STOP buttons on the CD player is pressed, a synchronized signal for stopping is output from the
EXT. SYNC. jack.
• Refer to figure 2 to connect the equipment.
• Use a single RCA cable to connect the units' EXT. SYNC. OUT jacks with the units' EXT. SYNC. IN jacks.
Set the infrared remote sensors of all the units to "OFF" when using this function. Also set the same infrared
remote control codes for all the units. (Refer to "PRESET FUNCTIONS AND OPERATIONS" (See page 14).)
Failure to make these settings could result in malfunction.
1. Load the CD into DN-C635. Load unrecorded cassette tapes into all decks.
2. Set the reverse mode and Dolby NR of all decks.
3. Adjust the twin recording level of DN-780Rs. (Master/Slave switch set to OFF.)
4. Press the Twin recording button of DN-780R.
) button y of DN-C635. Recording starts all decks.
5. Press the PLAY ( 1
NOTE:
• Use tapes of the same times (lengths) as far as possible.
) button u of the DN-C635 to stop recording on all the connected units.
6. Press the STOP (
2
Figure 2
L R
R L
14

BEFORE SWITCHING OFF THE POWER

11
When you have finished using the CD player, before switching off the power be sure that the disc holder has been
closed with the OPEN/CLOSE (
CAUTION:
• Do not forcibly close the disc holder when the power is off. It may damage the unit when it is transported.
12

PRESET FUNCTIONS AND OPERATIONS

(1) List of Preset Functions
• Functions can be preset using the buttons on the front panel. These presettings are stored in a permanent
memory, so they are not cleared even when the power is turned off.
• The functions shown on the table below can be preset. Set the functions according to the usage purpose to
efficiently achieve even higher quality playback.
• One of the preset functions can be used to display information on this set (microprocessor version).
Preset function type
Preset type Selection of preset type.
Finish mode Setting of operation when playback ends.
DN-C635
Power on mode Setting of operation when power is turned on.
Setting of whether or not to perform the auto cue
Auto cue
operation and the audio startup level.
Setting of whether or not to automatically stop the servo
Auto stop
functions.
Program 1 Setting of whether or not to play program 1.
Program 2 Setting of whether or not to play program 2.
Program 3 Setting of whether or not to play program 3.
Setting of whether or not to use the end monitor function
DN-780R
End monitor
and monitor time setting.
Setting of whether or not to display the EOM and display
E.O.M.
time setting.
Setting of whether or not to standby at the next track
Next track standby
when the CUE button is pressed during playback.
Setting of operation when select knob is turned during
Next Track Reserve
playback.
Play speed Standard playing speed setting.
Delay start Delay start time setting.
Panel lock Selection of whether or not to enable the panel buttons.
Selection of whether or not to inhibit the panel switches
Play lock
during playback.
Selection of whether or not to lock ejecting during
Eject lock
playback.
Time mode Setting of play mode when power is turned on.
Frame display Selection of whether or not to display frames.
Text display Selection of time or text display.
) button.
5
Description
Set upon shipment
No.
from factory
Preset Type 1 1
Finish Next 2
Power On Standby 3
CueDet. -48dB 4
Sleep 30min 5
Program 1 OFF 6
Program 2 OFF 7
Program 3 OFF 8
End Mon. 10 s 9
E.O.M. 10 s 10
Next Stb. OFF 11
Reserve. OFF 12
Normal Speed 13
Delay OFF 14
Panel OFF 15
Play Lock OFF 16
Eject OFF 17
Time REMAIN 18
FR Disp ON 19
Text OFF 20