Start Up; Operation; Program Selection - Windsor Radius 28 Manual Del Usuario

Installing and connecting the battery
Note
There is a built-in battery and charger.
Remove the lid of the battery compart-
ment.
Turn out the screw and remove the bat-
tery cover.
Insert battery in battery mount.
Warning
Pay attention to correct poles.
Attach the connection cable provided with
the pack.
Connect pole terminal (red cable) to
positive pole (+).
Connect pole terminal to negative pole
(-).
Replace the battery cover and fasten
using screw.
Replace the lid of the battery compart-
ment and lock it.
Note
Before removing the battery, make sure
that the negative pole lead is disconnected.
Check that the battery pole and pole termi-
nals are adequately protected with pole
grease.
Warning
Charge the battery before using the ma-
chine.
Charging battery
Danger
Risk of electric shock. Observe supply net-
work and fuse protection - see "Charger".
Only use the charger in dry rooms with suf-
ficient ventilation!
Note
The charging time for an empty battery is
approx. 12 hours.
Danger
Risk of injury! Comply with safety regula-
tions on the handling of batteries. Observe
the directions provided by the manufacturer
of the charger.
(1) Charging process for Bp Pack model
Danger
Risk of injury! The charger should be used
only if the mains cable is in an undamaged
state. Get the manufacturer, the customer
service agent or a qualified person to imme-
diately replace a damaged mains cable.
Note
Normally, the machine is equipped with a
maintenance-free battery.
Insert the plug of the charger into the
socket.
Note
The charger has electronic controls and au-
tomatically switches off the charging pro-
cess. All functions of the machine are
automatically shut down during the charg-
ing process.
The battery display shows the progress of
the charging process when the plug is in-
serted:
Battery is being charged
Battery is charged
Charger is defective glows red
Battery poled or is not slowly blinks red
connected
Battery defective blinks red fast
(2) Charging process for Bp model
Insert the charging cable of the charger
in the charger box of the sweeper
Plug in mains connector and switch on
charger.
After charging
Bp Pack model:
Remove the mains cable and put it
away:
– Insert the mains plug in the appliance
hood.
or
– Open the battery compartment, stove
the cable with the plug next to the bat-
tery, replace the lid of the battery com-
partment and lock it in.
Bp model:
Switch off the charger and remove the
plug from the socket.
Hang out the charging cable out of the
machine.
Close the cover of the battery compart-
ment.
Maximum battery dimensions
Length Width
175 mm 166 mm

Start up

Adjust the pushing handle
Figure 3, see cover page
Loosen both the star grips.
Pull the pushing handle backward and
tilt it to the desired position.
Press the pushing handle forward and
lock it in.
Tighten the star handles.
Figure 4, see cover page
1 OFF - Appliance is switched off.
2 Sweep.
3 Sweep suction (only DeLuxe model).
glows yellow
glows green
Warning
Do not sweep up packing strips, wire or
similar objects as this may damage the
sweeping mechanism.
The drive belts of the side brushes can slip
down. Tilt up the side brushes only when
the appliance is switched off.
Note
To achieve an optimum cleaning result, the
driving speed should be adjusted to take
specific situations into account.
Note
During operation, the waste container
should be emptied at regular intervals.
Note
Also lower side brush when cleaning along
edges.
Tilt the side brushed upward or down-
ward depending on the task.
Note
The dust blown up by the side brushes is
not sucked in. Place the side brushes at the
edge only while sweeping.
Set the programme switch to sweep or
sweep suction.
Dry floor
Wet floor
Move the appliance over the surface to
be swept.
Adjust the brush contact pressure
Height
Lift, adjust and lower the lever for the
125 mm
contact pressure of the sweeping roller.
+ Increase contact pressure.
– Reduce contact pressure.
Adjust the pressure by turning the turn-
ing handle for the contact pressure of
the side brushes.
+ Increase contact pressure.
– Reduce contact pressure.
Figure 5, see cover page
Note
A very high contact pressure means in-
creased power consumption and hence
lesser usage time.

Operation

Program selection

Sweeping mode
Sweep Sweep
suction
Sweep Sweep
English 7