Shutdown; Maintenance And Care - Windsor Radius 28 Manual Del Usuario

Collect dirt
Figure 6, see cover page
Slightly press the pushing handle down-
ward so that the appliance lifts up slight-
ly towards the front.
Move the appliance with the raised up-
per part over the dirt.
Now lower the appliance again.
Battery display
The battery display shows the charging sta-
tus of the battery during operations:
full
30% capacity remaining
10% capacity remaining
Protection against total
discharge; the appliance
is switched off
Emptying waste container
Warning
Risk of injury on account of rotating roller
brush.
Before removing the waste container
please turn the programme selection to
"OFF" and wait until the roller brush comes
to a halt.
Note
Dust progress. As far as possible, shake off
the filter and empty the waste container in
open places.
Turn the program selection switch to
"OFF".
Only DeLuxe model: Pull the handle of
the filter shake-off many times and rele-
aes it.
Only DeLuxe model: Tilt the dust suc-
tion upward.
Pull the waste container upward at the
handle and remove it from the appli-
ance.
Figure 7, see cover page
Dispose off the waste according to local
regulations.
Transport
Turn the program selection switch to
"OFF".
Lift the appliance at the carrying han-
dles when you want to transport it.
Secure the wheels of the machine with
wheel chocks.
Secure the machine with tensioning
straps or cables.
8 English
If the sweeper is going to be out of service
for a longer time period, observe the follow-
ing points:
Park the sweeper on an even surface.
Lock the sweeper to ensure that it does
not roll off.
Clean the inside and outside of the
sweeper.
Warning
Danger of damage to the machine because
of water penetrating into the machine! The
machine should not be sprayed using a
high pressure water jet.
Park the machine in a safe and dry
glows green
place.
glows yellow
Disconnect battery.
Charge battery and recharge it approx.
blinks red
every 2 months.
glows red

Maintenance and care

Danger
Risk of injury. Before performing any tasks
at the machine, first turn the programme se-
lection switch to "OFF"and clamp the cable
at the minus pole of the battery.
Cleaning the inside of the machine
Danger
Risk of injury! Wear dust mask and protec-
tive goggles.
Clean machine with a cloth.
Blow through machine with compressed
air.
External cleaning of the appliance
Clean the machine with a damp cloth
which has been soaked in mild deter-
gent.
Note
Do not use aggressive cleaning agents.
Maintenance intervals
Daily maintenance:
Check the sweeping roller and the side
brush for wear and wrapped belts.
Check function of all operator control el-
ements.
Weekly maintenance:
Clean both the foam filters under flow-
ing water.
Only DeLuxe model: Check flat-fold fil-
ter.
Check moving parts for freedom of
movement.
Check the sealing strips in the sweeping
area for wear.
Half-yearly maintenance:
Check tension, wear and tear and func-
tioning of the drive belts.
Maintenance following wear:
Replace sealing strips.
Replace roller brush.
Replace side brush.
For description, see section on Mainte-
nance work.

Shutdown

Note
Where maintenance is carried out by the
customer, all service and maintenance
work must be undertaken by a qualified
specialist. If required, a specialised Archer
dealer may be contacted at any time.
Maintenance Works
Preparation:
Park the sweeper on an even surface.
Turn the program selection switch to
"OFF".
Replacing side brush
Loosen 3 fastening screws.
Replace side brushes and tighten the
screws.
Replacing roller brush
It is necesary to replace them if the sweep
results are visibly poorer due to wear and
tear of the brushes and it is not possible to
readjust them using "Lever contact pres-
sure of sweep roller".
Remove the waste container.
Figure 8, see cover page
Pull the lever for contact pressure of
sweep roller fully backwards.
Loosen 3 screws each on both the sides
of the sweep roller.
Separate the roller halves and remove
them.
Place new roller halfs on the sweep roll-
er shaft. Ensure that the pins are sitting
correctly.
Fix in the screws and tighten them.
Replace the sealing strips
Loosen the screws as shown in the re-
spective diagram.
Remove the sealing strip and replace it
with a new sealing strip.
Fix in the screws and tighten them.
Front sealing strip (at the waste contain-
er)
Figure 9, see cover page
Rear sealing strip
Figure 10, see cover page
Side sealing strips
Figure 11, see cover page
Replace flat fold filter (only DeLuxe mod-
el).
Pull the handle of the filter shake-off
many times and releaes it.
Tilt the dust suction upward.
Figure 12, see cover page
Lift out the flat-fold filter and insert a
new flat-fold filter.
Cleaning the flat-fold filter
Remove both the foam filters.
Clean the foam filters under flowing wa-
ter and let them dry.
Push in the foam filters into the casing.
Ensure that the foam filters are gap-free
on all sides.