Fan Speed - Whirlpool ACQ082XK1 Manual De Uso

1. Press POWER ON/OFF to turn on air conditioner.
NOTE: When air conditioner is turned on for the first time
after it is plugged in, it will display the default settings: Cool
mode, Turbo fan speed, 72°F (22°C). When it is turned on at
all other times, it will display the previous settings.
2. Select mode. See "Mode."
3. Select fan speed. See "Fan Speed."
4. Select temperature. See "Temperature."
Mode
1. Press MODE until you see the indicator light come on for the
setting you want.
2. Choose AUTO, COOL, FAN or POWER SAVER.
Auto—Cools room while it automatically controls fan
speed. You cannot change fan speed, but you can adjust
temperature by pressing the up arrow or down arrow.
Cool—Cools room. You can select fan speed by pressing
FAN SPEED. You can then adjust temperature by
pressing the up arrow or down arrow.
Fan Only—Only the fan runs. Display shows "FO" (fan
only).
NOTE: Fan runs on Turbo speed only.
Power Saver—Fan runs only when cooling is needed. Fan
stops running when the room temperature matches the
temperature you set.
Since the fan does not circulate the room air continuously,
less energy is used, but the room air is not circulated as
often. Use Power Saver when you are asleep or away
from home.

Fan Speed

NOTE: Fan Speed button will operate only when Cool or Power
Saver mode has been selected.
1. Press FAN SPEED until you see the indicator light come on
for the setting you want.
2. Choose TURBO, HIGH or LOW.
10
Power
ON/OFF
AUTO
COOL
FAN
POWER
SAVER
MODE
TURBO
HIGH
LOW
FAN
SPEED
Temperature
Press the up arrow to raise the temperature. Each time you press
or hold the up arrow, the temperature will go up 1° until it reaches
86°F (30°C).
Press the down arrow to lower the temperature. Each time you
press or hold the down arrow, the temperature will go down 1°
until it reaches 64°F (18°C).
To change the temperature display from °F to °C:
1. Turn the air conditioner off.
2. While the air conditioner is off, press and hold down the
MODE and FAN SPEED buttons while pressing POWER ON/
OFF to turn the air conditioner on. The air conditioner will turn
on and display the °C settings.
NOTE: Follow these same steps to change the temperature
display from °C to °F.
Timer delay
To set the Timer for a 1- to 24-hour delay until the air
conditioner turns off (the air conditioner must be On):
1. Press TIMER ON/OFF. Indicator light will flash.
2. Press the up arrow or down arrow button to change delay
time (1 to 24 hours).
3. Press TIMER ON/OFF again or wait 10 seconds. Indicator
light will remain on.
To set the Timer to turn on the air conditioner, keeping
previous settings:
1. Turn air conditioner off.
2. Press TIMER ON/OFF. Indicator light will flash.
3. Press the up arrow or down arrow button to change delay
time (1 to 24 hours).
4. Press TIMER ON/OFF again or wait 10 seconds. Indicator
light will remain on.
To set the Timer to turn on the air conditioner, changing
the previous settings:
1. Turn air conditioner on.
2. Adjust MODE to Auto, Cool, Fan, or Power Saver.
3. Adjust FAN SPEED to Turbo, High or Low.
4. Adjust temperature between 64°F (18ºC) and 86°F (30ºC).
5. Wait 3 seconds before turning air conditioner off.
6. Press TIMER ON/OFF. Indicator light will flash.
7. Press the up arrow or down arrow button to change delay
time (1 to 24 hours).
8. Press TIMER ON/OFF again or wait 10 seconds. Indicator
light will remain on.
TIMER
ON/OFF