Publicidad
Idiomas disponibles
Idiomas disponibles
Your new tractor
has been assembled
at the factory with the exception
of those parts left
unassembled
for shipping
purposes°
To ensure
safe and proper operation
of your tractor
al! parts and hardware
you assemble
must be tightened
securely.
Use the correct tools as
necessary
to ensure
proper tightness°
TOOLS
REQUIRED
FOR ASSEMBEY"
.... A socket
wrench
set will make assembly
easier. Standard
wrench
sizes are listed.
(t) 5/I6"
wrench
Utility knife
(2) 7/i 6" wrenches
Tire pressure
gauge
(2) 1/2" wrenches
Pliers
(1) 9/16" wrench
When
right or left hand is mentioned
in this
manual, it meanswhenyou
are in the operating
position (seated behind the steering wheel),
TO
REMOVE
TRACTOR
FROM
CARTON
UNPACK
CARTON
1. Remove
all accessible
loose parts and
parts boxes from carton,,
2.
Cutalong
dashed
lines on allfour
panels
of carton.
Remove
end panels
and lay
side panels
flat.
3.
Check for any additional
loose parts or
cartons
and remove.
BEFORE
REMOVING
TRACTOR
FROM SKID
CHECK
BATTERY
1, Lift seat pan to raised position.
NOTE:
If this battery
is put into service after
month and year indicated
on label (label lo-
cated between
terminals)
charge battery for
minimum
of one hour at 6 - 10 amps.
(See
"BATTERY"
in Maintenance
section
of this
manual
for charging
instructions),
Seat
Terminal
Terminal
ATTACH
STEERING
WHEEL
ASSEMBLE
EXTENSION
SHAFT AND
BOOT
1. Slide extension
shaft onto lower steering
shaft.
2.
Place tabs of steering boot overtab
slots
in dash and push down to secure.
INSTALL
STEERING
WHEEL
3.
Position
front wheels
of the tractor
so
they are pointing
straight
forward,
4o Remove
steering
wheel
adapter
from
steering
wheel
and slide
adapter
onto
.....
steering
shaft extension,
5.
Position steeringwheelso
cross bars are
horizontal
(left to right) and slide inside
boot and onto adapter_
6. Assemble
large flat washer,
5/16 lock
washer,
5/16
hex bolt and tighten
se-
curely.
7,
Snap steering
wheel insert into center of
steering
wheel°
8.
Remove protective
materials from tractor
hood and grill.
IMPORTANT:
Check
for and remove
any
staples in skid that may puncture tires where
tractor
is to roll off skid°
L°lnsert
ck
Bolt -_}_
Washer
_c_---_Large
Fla! Washer
._.__.Steering
Wheel
Steering
Boot
Adapter---_____,(_
_
Extension
_.___-_Shaft
Lower
\_( .....
Steering
_'P"
........
Shaft ____.,
k
'""---.-°",,
I ./5_,;1_
-'%
',
Tab
{_P--' ':_"'_
1'\
Stot--"t_ [
_i./
}
INSTALL
SEAT
t.
Remove
bolt and flat washer
securing
seat to cardboard
packing and set aside
for assembly
of seat to tractor. Remove
the cardboard
packing
and discar&
2,
Connect
switch to seat.
3_ Place seat on seat pan so all three (3)
bottom
pads are positioned
over large
slotted
holes in pan.
4,
Push down on seat to engage
pads in
slots and pull seat towards rear of tractor,
5.
Raise seat and tighten bolt securely,
B
CONTROLAI
Si el tractor _
pararse a un_
mAs alto en u
seco o pavirn_
y ajustar eFfr(
CONTROL D
1_ Aparcar e
de hormic
el pedal c
el freno d
2.
Desembn
mando de
misi6n de
rueda libr
asi se col
Las ruedas tr
tinar cuando
el tractor man
freno o contac
de servicio CL
PARA REMO
REPARAClO
1.. Bloquee
2.
Remueva
ci6n y las
de ias rue
llave cuac
3.
Repare la
AVISO: En la.,
las ranuras el
ejeo inserte la
4o Vuelvaac_
de retencid
5. Vuefva a c(
AVISO: Pare
prevenir que t
pequefias fuc
Sears y utilizer
que las Ilanta.,
Anillc
Rete_
Cubierta
'
del eje
Llave Cuadrada
trasera solamer
IMPRESION 1
DELANTERA
La impresi6n
teras de sun
y son
normal
rJe las ruedas
caso que se F
impresi6n o I_
teras tel corn(
contacto con {
centro de sen
Publicidad
