NUTOOL BT211N Manual De Instrucciones página 26

Anleitung KGST 210/1
GB
The machine is to be operated only with tools
�
which conform with prEN 847-1: 1996.
Faulty saw blades have to be replaced
�
immediately.
Never use saw blades which do not comply with
�
the data specified in this manual.
Make sure that the arrow on the saw blade
�
complies with the arrow marked on the machine.
Make certain that the saw blade does not touch
�
the rotary table in any setting. To do so, pull out
the power plug and tilt the saw blade by hand into
the 45° position and the 90° position. If
necessary, re-adjust the saw head as described
in Section C/F.
It is imperative to make sure that all the devices
�
used to cover the saw blade are in good working
order.
Never wedge the hinged guard hood in open
�
position.
Never dismantle the machine's safety devices or
�
put them out of operation.
Damaged or faulty safety devices have to be
�
replaced immediately.
Never cut workpieces which are too small to hold
�
securely in your hand.
Do not place your hands in awkward positions
�
where one or both may slip suddenly and touch
the saw blade.
When working with long workpieces, use an
�
additional support (table, stand, etc.) to prevent
the machine from tipping over.
Always clamp round workpieces such as dowel
�
rods etc. with suitable devices.
There must be no nails or other foreign bodies in
�
that part of the workpiece you want to cut.
Always stand to the side of the saw blade when
�
working with the saw.
Never load the machine so much that it cuts out.
�
Always press the workpiece firmly against the
�
table and the stop rail to prevent it from wobbling
or twisting.
Make sure that off-cuts can be removed from the
�
side of the saw blade. If not, they may catch on
the saw blade crown and be catapulted into the
surrounding area.
Never saw several workpieces simultaneously.
�
Never remove loose splinters, chips or jammed
�
pieces of wood when the saw blade is running.
To rectify faults or remove jammed pieces of
�
wood, always switch off the machine first.
- Pull out the power plug! -
Conversions, adjustments, measurements and
�
cleaning jobs are to be performed only when the
motor is switched off. - Pull out the power plug! -
19.09.2002 18:49 Uhr
Before you switch on the machine, check that all
�
wrenches and adjustment tools have been
removed.
When you leave your workplace, switch off the
�
motor and pull out the power plug.
Electric installation work, repairs and
�
maintenance are to be carried out only by
specialists.
All guards and safety devices have to be refitted
�
immediately after completion of any repairs or
maintenance.
It is imperative to observe the manufacturer's
�
safety, operating and maintenance instructions
as well as the dimensions quoted in the technical
data.
It is imperative to observe the accident
�
prevention regulations in force in your area as
well as all other generally recognized rules of
safety.
Note the information published by your
�
professional associations.
Switch on the dust extraction system each time
�
you use the machine.
The machine may be used in closed rooms only
�
in conjunction with a suitable vacuum extraction
system.
The cross-cut saw must be connected to a 230 V
�
socket-outlet with a minimum 10 A fuse.
Never use light-duty machines for heavy-duty
�
work.
Never use the cable for any purpose other than
�
that for which it is intended!
Adopt a firm standing position and keep your
�
balance at all times.
Check the tool for signs of damage!
�
Before you carry on using the tool it is imperative
�
to check that its safety devices and any slightly
damaged parts are working properly and in the
way intended.
Check that the moving parts work properly and
�
do not jam or whether any of the parts are
damaged. All parts must be fitted correctly and
satisfy all conditions for the tool to work properly.
Unless otherwise stated in these instructions,
�
damaged safety devices and parts must be
repaired or replaced by experts in an approved
specialist workshop.
Have damaged switches replaced by a customer
�
service workshop.
This tool complies with the pertinent safety
�
regulations. Repairs are to be carried out only by
qualified electricians using original replacement
parts. The user may suffer an accident if this
condition is not observed.
Be careful when working in vertical mode.
�
26
Seite 17
GB
17