Technical Data; General Information - NUTOOL BT211N Manual De Instrucciones

Anleitung KGST 210/1
GB
Caution! Special care is required when making
�
double mitre cuts.
Do not overload your tool!
�
Wear safety goggles.
�
Wear a breathing mask on dusty jobs.
�
Examine the power cable / extension cable for
�
damage.
�
Wear goggles
�
Wear ear-muffs
�
Wear a breathing mask
Noise emission values
The saw's noise is measured in accordance with
�
DIN EN ISO 3744; 11/95, E DIN EN 31201; 6/93,
ISO 7960 Annex A; 2/95. The machine may
exceed 85 dB(A) at the workplace. In this case,
noise protection measures need to be introduced
for the user (ear-muffs).
Sound pressure level LPA
Sound pressure level LPA
Sound power level LWA
Sound power level LWA
Acceleration value = 1,814 m/s
„The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighbouring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved."
18
19.09.2002 18:49 Uhr
Cutting Idling
Cutting Idling
98,2 dB(A) 93,3 dB(A)
92,4 dB(A) 93,3 dB(A)
111,2 dB(A) 106,3 dB(A)
105,4 dB(A) 106,3 dB(A)
2
27
Seite 18

5. Technical data

Asynchronous motor
Voltage
Power rating
Power rating
Operating mode
Operating mode S1. 1200W S6. 25% 1500W
Idle speed n0
No load speed
Carbide saw blade
Number of teeth
Connector for dust extractor
Standing area
As bench-type circular saw:
As bench-type circular saw:
Saw table Saw table
Cutting height Cutting height
Parallel stop swinging range
Parallel stop swinging range
As mitre box saw: As mitre box saw:
Tilting range
Tilting range
Mitre cuts
Mitre cuts
Saw bed support
Saw bed support
Max. cross cut at 90°
Sawing width at 90°
Max. mitre cut at 45°
Sawing width at 45°
Max. bevel cut at 45°
Sawing width at 2 x 45°
Max. compound cut 45° x 45°
(double mitre cuts)
Weight
6. Before putting the machine into
operation (Abb. 1-3)

6.1 General information

The machine has to be set up where it can stand
�
firmly, e.g. bolt it to a work bench, a universal
base or similar.
All the covers and safety devices have to be
�
properly fitted before the machine is switched on.
It must be possible for the saw blade to run
�
freely.
When working with wood that has been
�
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
�
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
Before you connect the machine to the power
�
supply, make sure the data on the rating plate is
the same as that for your mains.
6.2 Converting the combination saw
The saw has two working positions:
A: Bench-type circular saw (Fig. 1)
B: Cross-cut and mitre box saw (Fig. 2)
GB
230 V 50 Hz
220-240 V ~ 50 Hz
1200 W
1500 W
S1
4600 rpm
5000 min
-1
ø 210 x ø 30 x 2.5 mm
24
ø 35 mm
400 x 285
360 x 250 mm 384 x 270 mm
0 - 33 mm 0 ÷ 33 mm
-30º a +30º
-30° to +30°
- 45º / 0º / +45º
-45° / 0° / +45°
0º to 45º to the left
0° to 45° to the left
390 x 140 mm
390 x 140 mm
55 x 115 mm
120 x 55 mm
52 x 77 mm
65 x 55 mm
40 x 110 mm
35 x 95 mm
40 x 23 mm
10 kg