Dry Vacuuming; Wet Vacuuming; Replacing The Power Cable - EINHELL TE-VC 2025 SACL Manual De Instrucciones Original

Crevice nozzle (Fig. 3)
The crevice nozzle (23) is designed for vacu-
uming solids and liquids in corners, edges and
other areas that are diffi cult to access.
Upholstery nozzle (Fig. 3)
The upholstery nozzle (26) is specially designed
for vacuuming solids on upholstery and carpets.
6. Operation
6.1 ON/OFF switch (Fig. 1/7)
Switch position 0:
Switch position I:
Switch position AUTO:
6.1.2 Suction power adjuster (Fig. 1a)
Turn the rotary knob for suction power adjustment
(16) to the left or right to adjust the suction power.

6.2 Dry vacuuming

Use the pleated fi lter (24) for dry vacuuming (see
point 5.2). The dirt bag (27) can be fi tted in additi-
on when removing particularly stubborn dirt (see
point 5.3).
Always ensure that the fi lters are securely seated.

6.3 Wet vacuuming

For wet-vacuuming, use the foam fi lter (25) (see
point 5.2).
Check that the fi lter is securely seated at all times.
Water drain screw (Fig.1)
To make the tank (10) easier to empty after wet
vacuuming, it is fi tted with a water drain screw
(11). Open the water drain screw (11) by turning it
anti-clockwise and drain the liquid.
When wet vacuuming, the fl oating safety switch
(Fig. 2/21) closes when the maximum tank level
is reached. At the same time, the suction noise of
the equipment will change and become louder.
You must then switch off the equipment and em-
pty the tank.
Danger!
The wet and dry vacuum cleaner is not suitable
for the vacuuming of combustible liquids.
For wet vacuuming, use only the supplied foam
fi lter.
Anl_TE_VC_2025_SACL_SPK9.indb 24 Anl_TE_VC_2025_SACL_SPK9.indb 24
GB
6.4 Automatic mode (Fig. 1)
Connect the power cable on your electric tool to
the automatic socket-outlet (4) and connect the
suction hose (9) to the extractor connector on
your electric tool. Check that the connections are
secure and air-tight.
You can use the supplied electric tool adapter
(Fig. 3/22) to connect the suction hose (9) to the
electric tool. To do so, fi t it between the suction
hose and the extractor port on the electric tool.
Set the switch (7) on the wet and dry vacuum
cleaner to position AUTO (automatic mode). The
Off
moment you switch on the electric tool, the wet
Normal mode
and dry vacuum cleaner switches on as well.
Automatic mode
When you switch off the electric tool, the wet and
dry vacuum cleaner switches off as well after a
pre-set delay.
6.5 Blowing
Connect the suction hose (Fig. 1/9) to the blow
connector (Fig. 2/19) on the wet and dry vacuum
cleaner.
6.6 Filter cleaning system (Fig. 19)
The equipment has a fi lter cleaning system which
enables large amounts of fi ne dust to be suc-
tioned without fi tting the dirt collector bag.
Important! The fi lter cleaning system can only be
activated if the equipment is in operation!
If there is a drop in suction performance, the fi lter
cleaning system can be activated at the touch of a
button in order to clean the dirty coarse fi lter and
increase the suction performance again.
Actuate the cleaning button (1) six times while
the equipment is in operation with the end of the
suction hose. Keep the button pressed down for
4 seconds each time you actuate it. Ensure that
the suction hose does not become kinked when
you do so.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
- 24 -
04.09.2020 09:51:12 04.09.2020 09:51:12