Geneva AeroSphère Large Guía De Configuración página 8

BACKPANEL
Radio antenna connector:
Input for external FM / DAB antenna.
F-Type connector.
Analog audio input
3.5 mm connector
STATUS LIGHT
yellow AeroSphére Base is starting up, this takes about 20 seconds
Successfully connected to the Wi-Fi network and successfully connected to at least one
green ( constant )
AeroSphère speaker
green ( slowly blinking ) Successfully connected to the Wi-Fi network
green ( fast blinking ) In the process of connecting to the Wi-Fi network
NYLLU  ZPUNSL ÅHZOPUN YLWLH[PUN  Wi-Fi setup in progress ( WPS method )
NYLLU  KV\ISL ÅHZOPUN YLWLH[PUN  Wi-Fi setup in progress ( network setup webpage method )
yellow / green / red ( changing ) Software update in progress
How to eject the CD
You can eject the CD with the following methods:
‹ Hold your hand about 10 mm above the CD slot. The CD eject
sensor is located above the CD slot. It detects the hand with a
proximity sensor.
‹ Use the button on the remote control
‹ Use the eject icon in the AeroSphère app
12
Wi-Fi SETUP:
Press: WPS push button setup method
Hold for 10 seconds: Network webpage setup method
DC power input
Connect to the AC power adapter connector
Status light Power switch
Shows current status, Power On / Off
see details below
VI WI-FI SETUP FOR THE AEROSPHÈRE BASE
Time required: 5 minutes
Once completed: the AeroSphère Base is connected to your Wi-Fi network. Now you are ready to use listen to FM, DAB+ and Audio CD from the
AeroSphère Base.
OVERVIEW
:[YLHTPUN -4 +() HUK H\KPV *+ ^PYLSLZZS` [V (LYV:WOuYL ZWLHRLYZ YLX\PYLZ [OL (LYV:WOuYL )HZL [V ÄYZ[ IL JVUULJ[LK [V [OL ZHTL >P-P
network. The AeroSphère Base must be in same Wi-Fi network as the AeroSphère speakers.
WI-FI SETUP METHOD WHEN TO USE THIS METHOD
WPS Your Wi-Fi router has a WPS push button for easy network setup.
Advanced method.
AeroSphère Network Setup webpage*
go to the "Feature Guide" on aerosphere.genevalab.com
 ,UHISLK I` KLMH\S[ ^OLU \ZPUN [OL (LYV:WOuYL ZWLHRLY MVY [OL ÄYZ[ time.
WAC is not supported on the AeroSphère Base
WI-FI SETUP WITH WPS
What is needed for this setup?
Your Wi-Fi router needs to support WPS. There is no computer or smartphone needed for this setup.
Instructions
1. Turn the AeroSphère Base on.
2. >HP[ \U[PS [OL Z[H[\Z SPNO[ ÅHZOLZ PU green.
3. Press the white "SETUP" button on the back of the AeroSphère Base.
4. On the Wi-Fi router press the WPS button. Typically a light on the
I\[[VU Z[HY[Z [V ÅHZO 0M UV[OPUN OHWWLUZ `V\ TH` OH]L [V OVSK [OL
button for a few seconds. The AeroSphère speaker and the Wi-Fi
router are now starting to connect to each other.
5. Wait until the status light changes from fast blinking green to
ÅHZOPUN NYLLU [V ZSV^S` ÅHZOPUN NYLLU @V\ HYL UV^ Z\JJLZZM\SS`
connected to your Wi-Fi network.
What is WPS?
WPS ( Wi-Fi protected setup ) is a simple way to connect a new device
to a Wi-Fi network. WPS is a common feature on today's Wi-Fi wireless
routers or Wi-Fi access points. After pushing the white "SETUP" button
WI-FI SETUP WITH THE AEROSPHÈRE NETWORK SETUP WEBPAGE
Follow the detailed description in the "Feature Guide" on aerosphere.genevalab.com
ENGLISH
Troubleshooting
‹ Repeat the procedure.
‹ Upgrade the software on your Wi-Fi router.
‹ Try the "AeroSphère Network Setup webpage" method in the
next chapter.
‹ Check the Genevalab.com support page.
on the AeroSphère Base and the "WPS" button on the Wi-Fi access
point, within about a minute the AeroSphère Base will automatically
connect to the Wi-Fi network.
13