Cardin BL Serie Manual De Instrucciones página 17

ELECTRICAL CONNECTION
Before connecting the appliance make sure that the voltage and fre-
quency rated on the data plate conform to those of the mains supply.
• The appliance works off a single phase 230 V 50 Hz power supply (see
wiring diagram).
• The geared motor must be earthed, to this end use the binding post
marked which can be found on the wiring box.
• Do not use cables with aluminium conductors; do not solder the ends
of cables which are to be inserted into the binding posts; use cables
which are marked T min 85°C and are resistant to atmospheric agents.
• The power cable must have enough slack to make sure it is not pulled
tight during normal operation.
• The power cable must not be wound around any of the appliances
components and must not be cemented into the wall.
An double pole circuit breaker with a minimum of 3 mm between
the contacts must be installed between the electronic programmer
and the mains supply.
• Connect the supplied capacitor between the live wires 2 and 3 of the
geared motor (fig. 19-21 pag. 9-11).
Power cable rubber sealing cap
1) Fit the sealing cap on to the power cable
and slide it down enough to allow you to
connect the cable to the terminal board.
2) Fasten down the cable using the cable
clamp.
3) Close the cover and slide the sealing cap
up over the cable entry opening.
This action is extremely important and will
guarantee a protection grade of IP44.
IMPORTANT! The geared motor is not fitted with a torque limiter.
Only use an electronic programmer which has a torque limiter with
maximum force at the head of the gate equal to 150 N (local stand-
ards and regulations in force).
SETTING THE MOTOR TORQUE (see electronic programmer)
When carrying out the installation you are advised to use a Cardin
electronic programmer fitted with a torque limiter.
The Cardin programmers optimise the correct working order of the "machine"
(motorised gates/doors) and guarantee full power maximum thrust at the
start of the opening/closing manoeuvre).
The programmer also guarantees that the effective torque fed to the system
will be that selected by the operator in the electronic programmer.
The choice of settings depends on the weight and size of the gate leaf/door
and the different environmental conditions on-site.
You are reminded that the standards and regulations in force unequivo-
cally require that the torque be set to a level suitable for the system.
Correctly choosing the torque will guarantee maximum security and long
life for the mechanical components.
SETTING THE MECHANICAL TRAVEL LIMIT (fig. 3 pag. 3)
The model 200/BL203C - 200/BL203CE is fitted with adjustable mechani-
cal travel limits "7" and "10".
Loosen the fastening screws and move the rings "7" and "10" to the
desired opening and closing positions then tighten them carefully.
(fig. 19-21 page 9-11)
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
SCALA: 1:2
Description : Prodotti Technocity
Drawing number :
DI0131
Collegamento gommino protezione
Product Code : BL202
Draft : P.J.Heath Date : 01-07-99
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
MANUAL RELEASE MECHANISM
Releasing the gate should only be carried out when the motor has stopped
because of blackouts.
To release the gate use the plastic key supplied with the appliance. It
should be stored in an easily accessible place, at home or on the appli-
ance itself using the key slot (pos. 5 fig. 12).
To release the gears
- open the lock mechanism cover by pressing on the sides (fig 12a-12b);
- insert the release key and turn it through about 30 degree (fig. 12c).
The gears will be released and the lock cylinder will rise;
- if you wish leave the gears released, just close the lock cylinder cover
(fig. 12e).
To lock the gears
- remove the key (fig. 12d), close the cover and press down with the
palm of your hand until the gears are locked;
- keep the key in a safe place.
Note: To make the operation easier the gate can be moved slightly if
required.
Don't force the locking mechanism, if you encounter resistance
move the gate slightly to allow the cogs to slot together more
easily within the geared motor.
17
(fig. 12, page 6)