Technical Specifications; Care And Maintenance - Shad BC03 Manual Del Usurario

button (1b). It will then cycle through three levels: LOW
< MEDIUM < HIGH < LOW...
Intercom pairing with a different SHAD
BC01, SHAD BC02 or a different
Bluetooth audio receiver.
®
Dual Link: Pairing as an intercom while maintaining
hands-free functionality:
• Complete pairing with the phone as described in the
paragraph above "Pairing to a mobile phone or GPS
navigator".
• Switch off Bluetooth
• Make sure both devices to be paired are switched off.
• Press and hold the control button (1b) of the SHAD
BC03 device until the LED indicator begins flashing in
Red and Blue.
• Press and hold the control button (1b) of the SHAD
BC01 or SHAD BC02 device until the LED indicator
begins flashing in Red and Blue. If you are using a
different device, put it in pairing mode.
• Briefly press the control button (1b) of the SHAD BC03
device once. After a few seconds, both devices will pair
and intercom functions will be activated. Once paired,
it is recommended for you to switch off the SHAD
BC03 device and switch it back on so that it operates
correctly with your phone and as an intercom.
The other intercom device will receive an acoustic
warning signal.
• Activate Bluetooth
on the phone, it will automatically detect the device
paired. Otherwise, you will need to select it manually.
NOTE: When two SHAD devices are in intercom mode,
incoming call functionality with their respective mobile
phones will be maintained. In case a call is received,
intercom functionality will stop and resume once the call
has ended.
Single Link: Pairing as an intercom only (without
hands-free features):
• Make sure both devices are switched off.
• Press and hold the control button (1b) of the SHAD
BC03 device until the LED indicator begins flashing in
Red and Blue.
• Press and hold the control button (1b) of the SHAD
BC01 or SHAD BC02 device until the LED indicator
12
on the phones.
®
on the phones again. Depending
®
begins flashing in Red and Blue. If you are using a
different device, put it in pairing mode.
• Briefly press the control button (1b) of the SHAD BC03
device once. After a few seconds, both devices will pair
and intercom functions will be activated. Once paired,
it is recommended for you to switch off the SHAD
BC03 device and switch it back on so that it operates
correctly with your telephone and as an intercom.
The other intercom device will receive an acoustic
warning signal.
Intercom functions:
Activating and deactivating intercom functions
between two SHAD devices: once both SHAD devices
have been paired and switched on, press the control
button (1b) of the SHAD BC03 for two seconds to
activate or deactivate intercom functionality.
Adjusting the volume for intercom functions: you
can adjust the volume by briefly pressing the control
button (1b). It will then cycle through three levels: LOW
< MEDIUM < HIGH < LOW...

Technical Specifications

Bluetooth : 2.1 Class 2
®
Profiles: A2DP stereo, HSP, HFP, EDR
Intercom frequency: 2.4 GHz
Battery: Lithium polymer, allowing for up to 7 hours of
talk time and 200 hours of standby time (depending on
use and configuration of the device)

Care and maintenance

The SHAD BC03 device uses components with
the latest technology and is manufactured to high
standards.
To keep your device from inadvertently becoming
damaged, please read the following recommendations
carefully:
• Do not attempt to open any of the system
components, since the electronic parts inside it may
become damaged. Do not attempt to open or change
the battery as it may be dangerous.
• Keep the SHAD BC03 out of the reach of children.
• Keep the SHAD BC03 in a dry place. Humidity and
condensation may damage the electronic circuits.
• Avoid exposing the device to extreme temperatures.
Intense cold may create condensation inside the