Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Replacing The Fuse
1.
Disconnect this product from power.
2.
Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.
3.
Remove blown fuse and replace with a good fuse of the same type and rating.
4.
Screw the fuse holder cap back in place and reconnect power.
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
DMX Linking
The Ovation H-605FC will work with a DMX controller using a 5-pin DMX serial or a hard wire connection. A DMX Primer
is available from
www.chauvetprofessional.com.
DMX Connection
The Ovation H-605FC uses a 5-pin DMX or a hard wire data connection for its DMX personalities: 1, 3, 5, 7, 10, 12, 13,
15, or HSV. See the User Manual for information about connecting and configuring the product for DMX operation.
Master/Slave Connection
The Ovation H-605FC uses the DMX data connection for its Master/Slave mode. See the User Manual for information
about how to connect and configure the product for master/slave operation.
RDM (Remote Device Management)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate bi-directionally
along existing DMX cabling. Check the DMX controller's User Manual or with the manufacturer as not all DMX controllers
have this capability. The Ovation H-605FC supports RDM protocol that allows feedback to make changes to menu map
options. Download the User Manual from
Wireless Operation
In optimal conditions, the Ovation H-605FC can operate up to 300 m (900 ft) away from the W-DMX transmitter. The W-
DMX receiver in the Ovation H-605FC must be paired with the W-DMX transmitter for wireless operation.
Initial Setup
1.
Turn the W-DMX transmitter on.
2.
Connect the W-DMX transmitter to a DMX controller.
3.
Place the Ovation H-605FC within 300 m from the W-DMX transmitter. Disconnect any DMX cable from the
Ovation H-605FC.
4.
Turn the Ovation H-605FC on.
Configuration
1.
From the Ovation H-605FC control panel, go to DMX Address.
2.
Select the start address, as with any other DMX compatible product.
3.
Go to Wireless Setting > Receive On/Off.
4.
Select On. (The Signal Strength Indicator will show a ? in front of the bars)
5.
Press the reset button on the W-DMX transmitter. (The Signal Strength Indicator on the Ovation H-605FC will
show a ϟ in front of the bars for 3 seconds while a connection is established.)
Product Pairing
If the Ovation H-605FC has already been paired with the W-DMX transmitter, the Signal Strength Indicator in the middle
of the LCD screen will show the strength of the signal. In this case, the Ovation H-605FC is ready to work in Wireless
mode. Pairing the Ovation H-605FC and a new W-DMX transmitter
1.
From the Ovation H-605FC's control panel, go to Wireless Setting.
2.
Select Receive Reset. The Signal Strength Indicator on the Ovation H-605FC will show a ? in front of the bars.
3.
From the W-DMX transmitter, press <RESET> (the Signal Indicator on the transmitter will flash).
4.
Once the transmitter has found the Ovation H-605FC, the Signal indicator on the W-DMX transmitter will
illuminate solid.
5.
The Signal Strength Indicator in the middle of the LCD screen on the Ovation H-605FC will show the strength of
the signal.
W-DMX operation can be interrupted or inhibited by liquid masses between the transmitter and
receiver such as water, snow, or people. For best results, keep the area between the transmitter
and receiver clear of any liquid mass.
Ovation H-605FC QRG Rev. 3
QUICK REFERENCE GUIDE
www.chauvetprofessional.com
for more details.
EN
2
Publicidad
Tabla de contenido
