General Power Tool Safety Warnings; Work Area Safety; Electrical Safety; Personal Safety - Lincoln PowerLuber 1880 Guía De Instalación Y Mantenimiento

Contents

General power tool safety warnings .

Specific safety . . . . . . . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . . . . . . .
Operation . . . . . . . . . . . . . . . . . . . . . .
Charger operation . . . . . . . . . . . . . . . .
Safety instruction for charger and
batteries . . . . . . . . . . . . . . . . . . . . . . . 11
Exploded view and parts list . . . . . . . 13
Troubleshooting . . . . . . . . . . . . . . . . . 15
To order call 1-800-548-1191 or visit www.partdeal.com - info@partdeal.com
General power tool
safety warnings
2
3
W a r n i n g
5
Read all safety warnings and instruc-
tions. Failure to follow the warnings and
5
instructions may result in electric shock,
fire and/or serious injury.
8
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings re-
fers to your mains-operated (corded) power
tool or battery-operated (cordless) power
tool.

Work area safety

Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.

Electrical safety

Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
Avoid body contact with earthed or
grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an in-
creased risk of electric shock if your body is
earthed or grounded.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entan-
gled cords increase the risk of electric shock.
When operating a power tool outdoors,
use an extension cord suitable for outdoor
2
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
If operating a power tool in a damp
location is unavoidable, use a Residual
Current Device (RCD) protected supply.
!
Notice
The term "residual current device
(RCD)" may be replaced by the term
"ground fault circuit interrupter (GFCI)"
or "earth leakage circuit breaker (ELCB)".

Personal safety

Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
Remove any adjusting key or wrench be-
fore turning the power tool on.
Power tool use and care
Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjustments,
changing accessories, or storing power
tools.
Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage
of parts and any other condition that may
affect the power tool's operation.
Use the power tool, accessories and tool
bits in accordance with instructions.