Jacuzzi sasha mi Manual De Instalación página 10

6a-6b) Check the position of the wall fastening elements
(
and install them.
7) Install the lower wall to the base frame so that:
(
- the ends of the fastening elements slide into those on the side
wall,
- the wood dowel is inserted into the frame profile.
8) Install the top wall onto the lower wall following the
(
previous instructions.
9) Install the glass-sauna frame as indicated.
(
NOTE: the frame must be inserted into the indicated metal dowels,
which can be adjusted to compensate for any offset.
10) Install the divider as indicated, sliding the audio speak-
(
ers through the bottom opening.
11) Install the glass-sauna panel as indicated.
(
12) Disconnect the cables indicated and remove the
(
shower panels.
13) Install the isolating multi-pole switch (with the cable
(
already connected to the appliance's junction box) in an area
that complies with the safety regulations as specified by current
legislation in force; the power supply line will be connected to
this switch.
NOTE: in the instance of a single-phase power supply
(220/240 V ~), you must suitably connect the terminals rela-
tive to the phases, as indicated.
Install the shower frame by fixing it to the divider (D) and shower
panel (P).
System configuration (micro-switches)
sc) Check that switch configuration corresponds to that in the
(
figure, in particular, switches "I2" must be positioned in this way:
1: - make sure the switch is in the OFF position.
2: - turn the switch to ON where installation of the Jacuzzi® audio
kit is planned;
- turn the switch to OFF otherwise;
3: - check that the switch is in the ON position.
4: - make sure the switch is in the OFF position.
5: - turn the switch to ON if you wish to carry out a demo function
of the equipment (trade fair, exhibition);
- turn the switch to OFF where normal operation is desired.
6: - turn the switch to ON where installation of the Jacuzzi® re-
mote control system is planned;
- turn the switch to OFF otherwise.
7: - make sure the switch is in the OFF position.
8: - act on the switch to save the positions of the modules con-
nected to the remote control system (see the instructions in-
cluded with the system).
Connections - 1
14) Connect the sauna audio speaker cables to the audio
(
box.
- Insert the display (A) and thermal fuse (B) cables into the con-
duit indicated.
15) Slide off the cable clamp from the temperature probe
(
(C) and thread it along with the cable (B) into the vertical con-
duit; anchor the cables using the foam rubber bushing.
- Wrap cable (C) and position it inside the display unit, leaving
enough room for the screen itself.
16) Connect the cable (B) to the terminal and thread the
(
probe (C) into the hole indicated; anchor the probe-holder to
the wall.
- Connect the cables (A) and (C) to the display and anchor it to
the wall.
17) Assemble the short backrest.
(
- Thread the power cord (D) into the wall conduit and position
the LED light strip onto the backrests; complete installation.
- Connect cord (D) to cord (D1) that exits the junction box.
Installing the structure - 2
18) Thread the heater cable (E) beneath the shower and
(
sauna frames into the position instructed.
NOTE: if supplied, fix the cable to the flexible hose of the heater's au-
tomatic filling device.
19) Assemble the skirting boards as indicated, making
(
sure that the heater cable (and hose, if present) are outside the
skirting.
20) When present, install the automatic filling device and
(
connect it to the flexible hose as indicated (items 1-2-4-5).
- Install the heater deflector, making sure that the correct version
is installed (left or right) item 3).
- Fix the brackets and the electrical box to the wall (holes present,
items 6-8). Apply the screws to hang the heater (item 7).
- Connect the electronic box cables to the heater unit; hang on
the brackets (items 9-10).
- Use running water to wash the stones, then dry them and place
them on the heater, ensuring to leave space between one stone
and another.
Do not place the stones in layers! Always try and leave
space between stones, so that hot air coming from be-
low can circulate freely.
10