Restoring Factory Settings; Technical Specifications - Orbis NEO ML+ Manual De Instrucciones

- EXTERNAL SENSOR MODE.
This mode is selected when the internal sensor is not selected and there
is an external sensor connected to the corresponding terminals.
IMPORTANT NOTE: This mode is only available with Heating.
The following symbol is displayed onscreen when EXTERNAL SENSOR
MODE is activated:
The ambient temperature corresponds to the
temperature measured by the external sensor.
In order to enter parameter configuration in EXTERNAL SENSOR
MODE, press the ▲ and ▼ buttons at the same time for five seconds.
Set ºC, will appear flashing on the screen, the ▲ and ▼ buttons are
used to choose equipment operation in either º F or º C. Confirm with
OK.
The words Hi Limits will start flashing on the screen. Use the ▲ ▼
buttons to select the upper temperature limit that can be programmed.
Confirm with OK.
Then the words Lo Limits will flash on the screen. Again use the ▲ ▼
buttons to select the lower temperature limit that can be programmed.
Confirm with OK.
The symbol now flashes on the display. Use the ▲ ▼ buttons to
select the COMFORT temperature. Confirm with OK.
Then the symbol will flash on the display. The ECO temperature can
be selected with the ▲ ▼ buttons. Press OK.
The word Diff. will start flashing on the screen. Use the ▲ ▼ buttons to
select the differential (the difference between the Switch On and Switch
Off temperatures) between the values: 0.6 ºC, 1 ºC, 2 ºC and 3 ºC.
IMPORTANT NOTE: regulation can be limited in this mode for
safety reasons. Thus, the COMFORT temperature cannot be
programmed higher than the Hi Limits temperature and the ECO
temperature cannot be programmed lower than the Lo Limits
temperature. The manual temperature adjustment
is also limited between these two protection temperatures.
This mode has an anti-icing temperature set at 10 ºC, which only takes
effect when the thermostat is switched to Standby
INTERNAL SENSOR + EXTERNAL SENSOR MODE
This mode is selected by installing the internal sensor jumper and
connecting an external sensor between the corresponding terminals.
IMPORTANT NOTE: This mode is only available with Heating.
The following symbol is displayed onscreen when INTERNAL SENSOR
+ EXTERNAL SENSOR MODE is activated:
The ambient temperature corresponds to the
temperature
sensor.
In order to enter parameter configuration in INTERNAL SENSOR +
EXTERNAL SENSOR MODE, press the ▲ and ▼ buttons at the same
time for five seconds. Set ºC, will appear flashing on the screen, the ▲
and ▼ buttons are used to choose equipment operation in either º F or
º C. Confirm with OK.
The symbol now flashes on the display, together with the Internal
Sensor symbol. Use the ▲ ▼ buttons to select the COMFORT
temperature. Confirm with OK.
Then the symbol will flash on the display, together with the Internal
Sensor symbol The ECO temperature can be selected with the ▲ ▼
buttons. Press OK.
The words Hi Limits will start flashing on the screen, together with the
External Sensor symbol. The ▲ ▼ buttons are used to select the upper
temperature limit at which the equipment will drop the load when the
external sensor reaches this temperature (this limit may be very useful
for protecting paving, depending on the employed material when radiant
floor is installed). Confirm with OK.
The word Diff. will start flashing on the screen, together with the Internal
Sensor symbol. Use the ▲ ▼ buttons to select the differential (the
difference between the Switch On and Switch Off temperatures)
between the values 0.2 ºC and 1 ºC in 0.2°C intervals.
IMPORTANT NOTE: this mode will switch off the load for safety
reasons when the external sensor reaches the Hi Limits
temperature. It is recommended that the COMFORT temperature
does not exceed this SWITCH-OFF temperature.
This mode has an anti-icing temperature set at 5 ºC, which only takes
effect when the thermostat is switched to Standby
(Ambient sensor or radiant floor)
.
(ideal for radiant floor)
measured by the
.
MANUAL TEMPERATURE ADJUSTMENT:
Press the ▲ or ▼ button and Set will be displayed with the
symbol
selected. This adjustment is made in 0.5ºC steps, after a few seconds,
the screen will, once again, display the ambient temperature.
SELECTING COMFORT AND ECO TEMPERATURES:
To activate the preselected COMFORT or ECO temperature, simply
press the corresponding button. The symbol will appear onscreen for two
seconds, together with the temperature at which it is programmed. In
order to modify the preselected COMFORT or ECO temperatures, follow
the steps described in the OPERATING MODE sections.

RESTORING FACTORY SETTINGS:

To restore the factory values, press
displayed and then reset the unit. The equipment is then configured with
the original factory settings.

TECHNICAL SPECIFICATIONS:

Power supply
Breaking power
Battery lifetime
Temperature measurement precision
Temperature update
Resolution
LCD measurement range:
Operation type
Output relay energises:
Every time the measurement or temperature adjustment is updated
Regulation type:
Regulation temperature
Upper Tº limit with external sensor
Lower Tº limit with external sensor
Protection class
Protection type
Operating temperature
Contamination situation
External sensor
DIMENSIONS:
internal
07/2011
. Press ▲ or ▼ again until the desired temperature is
Two alkaline batteries
LR03(AAA)1.5 V
µ 5(1) A 250 Vac
Approximately one year.
± 0.5 °C
Every 70 seconds.
0.1 °C
-10 ºC to +50 ºC
1B (Micro-switch off)
(Three-minute switch-on delay, only in cooling mode)
ON/OFF with adjustable
differential
Internal sensor: 5°C to 35°C
External sensor: 5ºC to 45 ºC
20 ºC to 45 ºC.
5 ºC to 20 ºC.
II according to EN 60335 for
correct installation.
IP40 according to EN 60529 for
correct installation.
0 °C to 50 °C.
Normal
NTC: 10 kΩ 25 ºC.
WARNING: when the load exceeds the maximum breaking
current, contactors are to be used
122
13 30 26 17
4
37,5 37,5
11
COTAS DE MONTAJE
ORBIS TECNOLOGIA ELECTRICA, S.A.
Lérida, 61
Telephone: +34 91 5672277;
E-mail: info@ orbis.es
http://www.orbis.es
for five seconds, until DEL, is
.
.
27
A016.32.55267
E-28020 MADRID
Fax: +34 91 5714006